lm258规格书.pdf

《lm258规格书.pdf》由会员分享，可在线阅读，更多相关《lm258规格书.pdf（12页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、?Product dataSupersedes data of 2002 Jan 22NE/SA/SE532LM258/358/A/2904Low power dual operational amplifiers2002 Jul 12INTEGRATED CIRCUITSPhilips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers22002 Jul 12853-1241 28616DESCRIPTIONThe 532/358/LM2904 consists

2、 of two independent,high gain,internally frequency-compensated operational amplifiers internallyfrequency-compensated operational amplifiers designed specificallyto operate from a single power supply over a wide range of voltages.Operation from dual power supplies is also possible,and the lowpower s

3、upply current drain is independent of the magnitude of thepower supply voltage.UNIQUE FEATURESIn the linear mode the input common-mode voltage range includesground and the output voltage can also swing to includes groundand the output voltage can also swing to ground,even thoughoperated from only a

4、single power supply voltage.The unity gaincross frequency is temperature-compensated.The input bias currentis also temperature-compensated.FEATURESInternally frequency-compensated for unity gainLarge DC voltage gain:100 dBWide bandwidth(unity gain):1 MHz(temperature-compensated)Wide power supply ran

5、ge single supply:3 VDC to 30 VDC,or dual supplies:1.5 VDC to 15 VDCVery low supply current drain(400 A)essentially independentof supply voltage(1 mW/op amp at+5 VDC)Low input biasing current:45 nADC temperature-compensatedLow input offset voltage:2 mVDC,and offset current:5nADCDifferential input vol

6、tage range equal to the power supply voltageLarge output voltage:0 VDC to V+1.5 VDC swingPIN CONFIGURATION12345678+ABV+OUTPUT BINVERTING INPUT BNON INVERTING INPUT BOUTPUT AINVERTING INPUT ANON INVERTING INPUT AVD,DP,and N PackagesSL00282Figure 1.Pin configuration.EQUIVALENT CIRCUITV+6 A100 AQ2Q3Q1Q

7、4INPUTS+Q8Q9CCQ106 AQ5Q7Q6RSCOUTPUTQ13Q12Q1150 ASL00283Figure 2.Equivalent circuit.Philips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 123ORDERING INFORMATIONDESCRIPTIONTEMPERATURE RANGEORDER CODEDWG#8-Pin Plastic Small Outline(SO)Package0 C to

8、+70 CNE532DSOT96-18-Pin Plastic Dual In-Line Package(DIP)0 C to+70 CNE532NSOT97-18-Pin Plastic Small Outline(SO)Package40 C to+85 CSA532DSOT96-18-Pin Plastic Small Outline(SO)Package40 C to+125 CLM2904DSOT96-18-Pin Plastic Thin Shrink Small Outline Package(TSSOP)40 C to+125 CLM2904DPSOT505-18-Pin Pl

9、astic Dual In-Line Package(DIP)40 C to+125 CLM2904NSOT97-18-Pin Plastic Small Outline(SO)Package25 C to+125 CLM258DSOT96-18-Pin Plastic Dual In-Line Package(DIP)25 C to+125 CLM258NSOT97-18-Pin Plastic Small Outline(SO)Package0 C to+70 CLM358DSOT96-18-Pin Plastic Thin Shrink Small Outline Package(TSS

10、OP)0 C to+70 CLM358DPSOT505-18-Pin Plastic Dual In-Line Package(DIP)0 C to+70 CLM358NSOT97-18-Pin Plastic Small Outline(SO)Package0 C to+70 CLM358ADSOT96-18-Pin Plastic Dual In-Line Package(DIP)0 C to+70 CLM358ANSOT97-18-Pin Plastic Dual In-Line Package(DIP)55 C to+125 CSE532NSOT97-1ABSOLUTE MAXIMUM

11、 RATINGSSYMBOLPARAMETERRATINGUNITVSSupply voltage,V+32 or 16VDCDifferential input voltage32VDCVINInput voltage0.3 to+32VDCMaximum power dissipation Tamb=25 C(Still air)1PDN package1160mWD package780mWDP package714mWOutput short-circuit to GND2V+15 VDC and Tamb=25 CContinuousOperating ambient tempera

12、ture rangeNE532/LM358/LM358A0 to+70CTambLM25825 to+85CTambLM290440 to+125CSA53240 to+85CSE53255 to+125CTstgStorage temperature range65 to+150CTsldLead soldering temperature(10 sec max)230CNOTE:1.Derate above 25 C,at the following rates:N package at 9.3 mW/CD package at 6.2 mW/CDP package at 5.72 mW/

13、C2.Short-circuits from the output to V+can cause excessive heating and eventual destruction.The maximum output current is approximately40 mA independent of the magnitude of V+.At values of supply voltage in excess of+15 VDC,continuous short-circuits can exceed thepower dissipation ratings and cause

14、eventual destruction.Philips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 124DC ELECTRICAL CHARACTERISTICSTamb=25 C;V+=+5 V,unless otherwise specified.SYMBOLPARAMETERTEST CONDITIONSSE532,LM258NE/SA532/LM358/LM2904UNITMinTypMaxMinTypMaxVOSOffset

15、voltage1RS=0 2527mVVOSOffset voltage1RS=0;over temp.79mVVOSDriftRS=0;over temp.77V/CIOSOffset currentIIN(+)IIN()330550nAIOSOffset currentOver temp.100150nAIOSDriftOver temp.1010pA/CISInput current2IIN(+)or IIN()4515045250nAIBIASInput current2IIN(+)or IIN();Over temp.4030040500nAIBDriftOver temp.5050

16、pA/CVCCommon-mode voltageV+=30 V0V+1.50V+1.5VVCMgrange3V+=30 V;Over temp.0V+2.00V+2.0VCMRRCommon-mode rejectionratioV+=30 V70856570dBVOOutput voltage swingRL 2 k;V+=30 V;over temp.2626VVOHOutput voltage swingRL 10 k;V+=30 V;over temp.27282728VVOLOutput voltage swingRL 10 k;over temp.520520mVRL=;V+=3

17、0 V0.51.00.51.0mAICCSupply currentRL=on all amplifiers;V+=30 V;over temp.0.61.20.61.2mARL 2 k;VOUT 10 V5010025100V/mVAVOLLarge-signal voltage gainV+=15V(for large VO swing);over temp.2515V/mVPSRRSupply voltage rejectionratioRS=0 6510065100dBAmplifier-to-amplifiercoupling4f=1 kHz to 20 kHz(input refe

18、rred)120120dBOutput current(Source)VIN+=+1 VDC;VIN=0 VDC;V+=15 VDC20402040mAOutput current(Source)VIN+=+1 VDC;VIN=0 VDC;V+=15 VDC;over temp.10201020mAIOUTVIN=+1 VDC;VIN+=0 VDC;V+=15 VDC10201020mAOutput current (Sink)VIN=+1 VDC;VIN+=0 VDC;V+=15 VDC;over temp.5858mAVIN+=0 V;VIN=+1 VDC;VO=200 mV1250125

19、0AISCShort circuit current540604060mADifferential input voltage6V+V+VGBWUnity gain bandwidthTamb=25 C11MHzSRSlew rateTamb=25 C0.30.3V/sVNOISEInput noise voltageTamb=25 C;f=1 kHz4040nV/Hz(Notes on next page).Philips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational ampl

20、ifiers2002 Jul 125DC ELECTRICAL CHARACTERISTICS(continued)Tamb=25 C;V+=+5 V;unless otherwise specified.SYMBOLPARAMETERTEST CONDITIONSLM358AUNITSYMBOLPARAMETERTEST CONDITIONSMinTypMaxUNITVOSOffset voltage1RS=0 23mVVOSOffset voltage1RS=0;over temp.5mVVOSDriftRS=0;over temp.720V/CIOSOffset currentIIN(+

21、)IIN()530nAIOSOffset currentOver temp.75nAIOSDriftOver temp.10300pA/CISInput current2IIN(+)or IIN()45100nAIBIASInput current2IIN(+)or IIN();Over temp.40200nAIBDriftOver temp.50pA/CVCCommon mode voltage range3V+=30 V0V+1.5VVCMCommon-mode voltage range3V+=30 V;Over temp.0V+2.0VCMRRCommon-mode rejectio

22、n ratioV+=30 V6585dBVOOutput voltage swingRL 2 k;V+=30 V;over temp.26VVOHOutput voltage swingRL 10 k;V+=30 V;over temp.2728VVOLOutput voltage swingRL 10 k;over temp.520mVICCSupply currentRL=,V+=30 V0.51.0mAICCSupply currentRL=on all amplifiers;V+=30 V;over temp.0.61.2mAAOLarge signal voltage gainRL

23、2 k;VOUT 10 V25100V/mVAVOLLarge-signal voltage gainV+=15 V(for large VO swing);over temp.15V/mVPSRRSupply voltage rejection ratioRS=0 65100dBAmplifier-to-amplifier coupling4f=1kHz to 20kHz(input referred)120dBVIN+=+1 VDC;VIN=0 VDC;V+=15 VDC2040mAOutput current(Source)VIN+=+1 VDC;VIN=0 VDC;V+=15 VDC;

24、over temp.1020mAIOUTVIN=+1 VDC,;VIN+=0 VDC;V+=15 VDC1020mAOutput current (Sink)VIN=+1 VDC;VIN+=0 VDC;V+=15 VDC;over temp.58mAVIN+=0 V;VIN=+1 VDC;VO=200 mV1250AISCShort circuit current54060mADifferential input voltage6V+VGBWUnity gain bandwidthTamb=25 C1MHzSRSlew rateTamb=25 C0.3V/sVNOISEInput noise

25、voltageTamb=25 C;f=1 kHz40nV/HzNOTES:1.VO 1.4 V,RS=0 with V+from 5 V to 30 V;and over the full input common-mode range(0 V to V+1.5 V).2.The direction of the input current is out of the IC due to the PNP input stage.This current is essentially constant,independent of the state ofthe output so no loa

26、ding change exists on the input lines.3.The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V.The upper end ofthe common-mode voltage range is V+1.5 V,but either or both inputs can go to+32 V without damage.4.Due to proximity of external

27、 components,insure that coupling is not originating via stray capacitance between these external parts.Thistypically can be detected as this type of capacitance coupling increases at higher frequencies.5.Short-circuits from the output to V+can cause excessive heating and eventual destruction.The max

28、imum output current is approximately40 mA independent of the magnitude of V+.At values of supply voltage in excess of+15 VDC,continuous short-circuits can exceed thepower dissipation ratings and cause eventual destruction.6.The input common-mode voltage or either input signal voltage should not be a

29、llowed to go negative by more than 0.3 V.The upper end ofthe common-mode voltage range is V+1.5 V,but either or both inputs can go to+32 VDC without damage.Philips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 126TYPICAL PERFORMANCE CHARACTERISTI

30、CSV OUTPUT VOLTAGE(V )O+VDC100 kVO1K+7VDCVIN2 kTamb=0 C to+125 CTamb=55 C43210010203040SUPPLY VOLTAGE(VDC)SUPPLY CURRENT DRAIN(mA )DC9080706050403020100553515525456585105 125TEMPERATURE(C)OUTPUT CURRENT(mA )DC16012080400010203040SUPPLY VOLTAGE(VDC)RL+20 kRL+2 kA VOLTAGE GAIN(dB)VOL+V+10MVO0.1 fV+/2V

31、INV+=30 VDC AND55 C Tamb +125 CV+=10 to 15 VDC AND55 C Tamb +125 C1401201008060402001101001k10k100k 1M10MFREQUENCY(Hz)VOLTAGE GAIN(dB)201510501k10k100k1MFREQUENCY(Hz)V OUTPUT SWING(V )OppRL 2 k V+15 VDC432103210010203040TIME(s)OUTPUT VOLTAGE(V)INPOUT VOLTAGE(V)EO50 pFINPUTOUTPUTIN5004504003503002500

32、12345678t TIME(s)Tamb=+25 CV+=+30 VDCE OUTPUT VOLTAGE(mV)O+V+/2V+V2IOINDEPENDENT OF V+TAamb=+25 C876543210.0010.010.1110100IO+OUTPUT SOURCE CURRENT(mADC)V OUTPUT VOLTAGEREFERENCE TO V+(VD )DCV+/2V+IOTamb=+25 CV+=+5 VDCV+=+15 VDCV+=+30 VDC1010.10.010.0010.010.1110100IO OUTPUT SINK CURRENT(mADC)DCVO+S

33、upply CurrentCurrent LimitingVoltage GainOpen-Loop Frequency ResponseLarge-Signal Frequency ResponseVoltage-Follower ResponseVoltage-Follower Pulse Response(Small-Signal)Output CharacteristicsCurrent SourcingOutput CharacteristicsCurrent SinkingSL00284Figure 3.Typical performance characteristics.Phi

34、lips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 127TYPICAL PERFORMANCE CHARACTERISTICS(Continued)+V INPUT VOLTAGE(V )15105NEGATIVEPOSITIVE051015V+OR V POWER SUPPLY VOLTAGE(+VDC)INDC+VCM=0 VDCV+=+30 VDCV+=+15 VDCV+=+5 VDC90807060504030201005535

35、 15525456585 105 125Tamb TEMPERATURE(C)I INPUT CURRENT(nA )BDC100 100 7.5 VDCVO100 k+VIN+7.5 VDC1201008060402001001k10k100k1Mf FREQUENCY(Hz)CMRR COMMONMODE REJECTION RATIO(dB)Input Voltage RangeInput CurrentCommonMode Rejection RatioSL00285100 kFigure 4.Typical performance characteristics(continued)

36、.TYPICAL APPLICATIONSV+2Non-Inverting AmplifierRFV+8RLVORINV+2VIN+4V+8VOVIN+4V+10 kV+8VOVIN+4V+RFBLOCKSDC.GAINR1Single Supply Inverting AmplifierInput Biasing Voltage FollowerSL0028610 k10 k10 kFigure 5.Typical applications.Philips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual

37、 operational amplifiers2002 Jul 128SO8:plastic small outline package;8 leads;body width 3.9 mmSOT96-1Philips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 129DIP8:plastic dual in-line package;8 leads(300 mil)SOT97-1Philips SemiconductorsProduct d

38、ataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 1210TSSOP8:plastic thin shrink small outline package;8 leads;body width 3 mmSOT505-1Philips SemiconductorsProduct dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 1211NOTESPhilips Semiconductors

39、Product dataNE/SA/SE532/LM258/358/A/2904Low power dual operational amplifiers2002 Jul 1212DefinitionsShort-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title.Fordetailed information see the relevant data sheet or data han

40、dbook.Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System(IEC 60134).Stress above oneor more of the limiting values may cause permanent damage to the device.These are stress ratings only and operation of the device at these orat any other condit

41、ions above those given in the Characteristics sections of the specification is not implied.Exposure to limiting values for extendedperiods may affect device reliability.Application information Applications that are described herein for any of these products are for illustrative purposes only.Philips

42、Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing ormodification.DisclaimersLife support These products are not designed for use in life support appliances,devices or systems where malfunction of these products can

43、reasonably be expected to result in personal injury.Philips Semiconductors customers using or selling these products for use in such applicationsdo so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.Right to make changes Philips S

44、emiconductors reserves the right to make changes,without notice,in the products,including circuits,standardcells,and/or software,described or contained herein in order to improve design and/or performance.Philips Semiconductors assumes noresponsibility or liability for the use of any of these produc

45、ts,conveys no license or title under any patent,copyright,or mask work right to theseproducts,and makes no representations or warranties that these products are free from patent,copyright,or mask work right infringement,unlessotherwise specified.Contact informationFor additional information please v

46、isithttp:/.Fax:+31 40 27 24825For sales offices addresses send e-mail to:.Koninklijke Philips Electronics N.V.2002All rights reserved.Printed in U.S.A.Date of release:08-02Document order number:9397 750 10187?Data sheet status1Objective dataPreliminary dataProduct dataProductstatus2DevelopmentQualif

47、icationProductionDefinitionsThis data sheet contains data from the objective specification for product development.Philips Semiconductors reserves the right to change the specification in any manner without notice.This data sheet contains data from the preliminary specification.Supplementary data wi

48、ll bepublished at a later date.Philips Semiconductors reserves the right to change the specificationwithout notice,in order to improve the design and supply the best possible product.This data sheet contains data from the product specification.Philips Semiconductors reserves theright to make changes

49、 at any time in order to improve the design,manufacturing and supply.Changes will be communicated according to the Customer Product/Process Change Notification(CPCN)procedure SNW-SQ-650A.Data sheet status1Please consult the most recently issued data sheet before initiating or completing a design.2The product status of the device(s)described in this data sheet may have changed since this data sheet was published.The latest information is available on the Internet at URLhttp:/.