33V_深圳市盈达顺科技有限公司WINCOM TECH,规格书.pdf

《33V_深圳市盈达顺科技有限公司WINCOM TECH,规格书.pdf》由会员分享，可在线阅读，更多相关《33V_深圳市盈达顺科技有限公司WINCOM TECH,规格书.pdf（17页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:1/17 Wincom Tech CO.,LTD.The LCD(M)Specialist CONTACT ADDRESS:3F,Block 13,WangJingKeng Industry Park,DaKan XiLi,NanShan,Shenzhen,China.http:/ PART NO.:WC2004B-SFYLYHC06-R(3.3V)FOR MESSRS.:CONTENTS NO.ITEM PAGE 1.COVER 1 2.RECORD OF REVISION 2 3.GENE

2、RAL SPECIFICATION 3 4.MECHANICAL DATA 3 5.ABSOLUTE MAXIMUM RATINGS 4 6.ELECTRICAL CHARACTERISTICS 5 7.OPTICAL CHARACTERISTICS 5 8.OUTLINE DIMENSION 67 9.BLOCK DIAGRAM 7 10 INTERFACE TIMING CHART 89 11 INSTRUCTION CODE 1011 12 CHARACTER GENERATOR ROM 12 13 SPECIFICATION OF QUALITY ASSURANCE 1317 ACCE

3、PTED BY:PROPOSED BY:Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:2/17 RECORD OF REVISION DATE PAGE SUMMARY 2013-2-19-NEW ISSUE Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:3/17 3.General specifications 3.1 General specifications PLEASE REFER TO:“CUSTOMER ACCEPTANCE STANDARD SPECIFICATIONS(

4、MS-10-10000)”.3.2 Quality Assurance and Warranty PLEASE REFER TO:“QUALITY ASSURANCE MANUL(MS-10-10001)“.3.3 This individual specification is prior to general specifications 4.General data Display format:20 characters x 4 lines Data transfer:4/8Bit Parallel LCD type:STN,Positive,Yellow-green,Transfle

5、ctive Backlight Color:Yellow-green,LED,Side backlight Viewing angle:6 oclock LCD controller:SPLC780 or equivalent Character Font:Russia Power supply:3.3V Module size:146 x 62.5 x 15.5mm View area:123 x 43 mm Dot size:0.93 x 1.1 mm Dot pitch:0.98 x 1.15 mm Driving method:1/16 duty,1/5Bias Wincom Tech

6、 CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:4/17 5.Absolute maximum ratings 5.1 Electrical absolute maximum ratings I T E M SYMBOL MIN.MAX.UNIT COMMENT POWER SUPPLY FOR LOGIC VDD-VSS-0.3 4 V-INPUT VOLTAGE VI VSS VDD V-STATIC ELECTRICITY-V VS 0 3.3 Vrms-POWER SUPPLY FOR BACKLIGHT fFL-KHz-Vrms Ta=25 STARTI

7、NG VOLTAGE FOR BACKLIGHT-Vrms Ta=25 POWER SUPPLY FOR LCD VDD-V0-4.7 V-5.2 Environmental absolute maximum ratings OPERATING STORAGE I T E M MIN.MAX.MIN.MAX.COMMENT AMBIENT TEMPERATURE-20 70-30 80-HUMIDITY NOTE(2)NOTE(2)NO CONDENSATION VIBRATION NOTE(3)-0.5G-2G 10300Hz XYZ DIRECTIONS 1 Hr EACH SHOCK N

8、OTE(3)-3G-5G 10 msec XYZ DIRECTIONS 1 TIME EACH CORROSIVE GAS NOT ACCEPTABLE NOT ACCEPTABLE-NOTE(2):Ta 70:75%RH MAX.Ta 70:ABSOLUTE HUMIDITY MUST BE LOWER THAN THE HUMIDITY OF 75%RH AT 70.NOTE(3):1G=9.8 m/s2 Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:5/17 6.Electrical characteristics Ta=25 VDD

9、=3.3 V I T E M SYMBOL CONDITION MIN.TYP.MAX.UNIT Power supply voltage for Logic circuit VDD-VSS-3.1 3.3 3.5 V Power supply voltage for LCD drive VDD-V0-4.7-V LCD display duty ratio DUTY-1/16-Ifp I mseo plus 10%Dutg cyele -mA Operating voltage 3.0 3.1 3.3 V LED BACKLIGHT Forward current-80 120 mA LED

10、 Lifetime-VFL=3.1Vrms IFL=80mA-100,000-Hr Power supply LCD current IEE VDD-V0=4.7 V-mA LED backlight:Due to the LED backlight working current is XXX Max,and LED chips Vop may be different,Wincom will adjust the backlight resistor according to the LED chips Vop,to meet the brightness maximum 7.Optica

11、l characteristics Ta=25 VDD-V0=4.7V I I I I T T T T E E E E M M M M SYMBOLSYMBOLSYMBOLSYMBOL CONDITIONCONDITIONCONDITIONCONDITION MIN.MIN.MIN.MIN.TYPTYPTYPTYP.MAX.MAX.MAX.MAX.UNITUNITUNITUNIT NOTENOTENOTENOTE Viewing angle 2-1 K 2.0-35-20 deg.1 Contrast ratio K =10O =0O 4.0-1 tr(rise)=10O =0O-250 ms

12、 1 Response time(at 25)tf(fall)=10O =0O-250 ms 1 The brightness of backlighting source B VFL=3.0Vrms If=80mA-220-cd/m2 2 NOTE(1):SEE CUSTOMER ACCEPTANCE STANDARD SPECIFICATION FOR DEFINITION OF OPTICAL CHARACTERISTICS NOTE(2):UNDER NORMAL TEMPERATURE AND HUMIDITY IN A DARK ROOM Wincom Tech CO.,LTD.W

13、C2004B-SFYLYHC06-R(3.3V)PAGE:6/17 8.Outline dimension Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:7/17 8.1 Interface Pin Assignment PIN NO.Symbol Leve Function 1 Vss 0V Ground 2 VDD 3.3V Power supply voltage for LCM(+)3 V0-Contrast Adjust 4 RS H/L Register select signal 5 R/W H/L Data read/wri

14、te 6 E H/L Enable signal 7 DB0 H/L Data bus line 8 DB1 H/L Data bus line 9 DB2 H/L Data bus line 10 DB3 H/L Data bus line 11 DB4 H/L Data bus line 12 DB5 H/L Data bus line 13 DB6 H/L Data bus line 14 DB7 H/L Data bus line 15 A(+3.3V)Power supply for LED BL(+)16 K(-)Power supply for LED BL(-)9.Block

15、diagram CONTROLDDLEDSPLC780 Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:8/17 10.Interface Timing Chart Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:9/17 11.Instruction Code Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:10/17 Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:11/17 12.C

16、haracter generator ROM Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:12/17 13.Specification of quality assurance AQL inspection standard Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:13/17 Sampling method:MIL-STD-105E,Level II,single sampling Defect classification(Note:*is not including)Clas

17、sify Item Note AQL Short or open circuit LC leakage Flickering No display Wrong viewing direction 1 Contrast defect(dim,ghost)2 Display state Back-light 1,8 Flat cable or pin reverse 10 Major Non-display Wrong or missing component 11 0.65 Background color deviation 2 Black spot and dust 3 Line defec

18、t,Scratch 4 Rainbow 5 Chip 6 Display state Pin hole 7 Protruded 12 Polarizer Bubble and foreign material 3 Soldering Poor connection 9 Wire Poor connection 10 Minor TAB Position,Bonding strength 13 1.5 Note on defect classification Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:14/17 No.Item Crit

19、erion Short or open circuit LC leakage Flickering No display Wrong viewing direction 1 Wrong Back-light Not allow Contrast defect 2 Background color deviation Refer to approval sample 3 Point defect,Black spot,dust(including Polarizer)=(X+Y)/2 Point Size Acceptable Qty.0.10 Disregard 0.100.20 3 0.20

20、0.25 2 0.250.30 0 Unit:mm 4 Line defect,Scratch Line Acceptable Qty.L W -0.015W Disregard 3.0L 0.03W 2.0L.05W 2 1.0L 0.1W 1-0.05W Applied as point defect 5 Rainbow Not more than two color changes across the viewing area.NO.Item Criterion Y X L W Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:15/1

21、7 6 Chip Remark:X:Length direction Y:Short direction Z:Thickness direction t:Glass thickness W:Terminal Width Acceptable criterion X Y Z 2 0.5mm t/2 Acceptable criterion X Y Z 2 0.5mm t Acceptable criterion X Y Z 3 2 shall not reach to ITO t Acceptable criterion X Y Z Disregard 0.2 t No.Item Criteri

22、on Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:16/17 7 Segment pattern W=Segment width =(X+Y)/2 (1)Pin hole 0.10mm is acceptable.8 Back-light(1)The color of backlight should correspond its specification.(2)Not allow flickering 9 Soldering(1)Not allow heavy dirty and solder ball on PCB.(The siz

23、e of dirty refer to point and dust defect)(2)Over 50%of lead should be soldered on Land.10 Wire(1)Copper wire should not be rusted(2)Not allow crack on copper wire connection.(3)Not allow reversing the position of the flat cable.(4)Not allow exposed copper wire inside the flat cable.11*PCB(1)Not all

24、ow screw rust or damage.(2)Not allow missing or wrong putting of component.NO.Item Criterion Wincom Tech CO.,LTD.WC2004B-SFYLYHC06-R(3.3V)PAGE:17/17 12 Protruded W:Terminal Width Acceptable criteria:Y 0.4 13 TAB 1.Position W11/3W H11/3H 2 TAB bonding strength test P(=F/TAB bonding width)650gf/cm,(speed rate:1mm/min)5pcs per SOA(shipment)14 Total no.of acceptable Defect A.Zone Maximum 2 minor non-conformities per one unit.Defect distance:each point to be separated over 10mm B.Zone It is acceptable when it is no trouble for quality and assembly in customers end product.