DTU40P06品牌授权规格书.pdf

《DTU40P06品牌授权规格书.pdf》由会员分享，可在线阅读，更多相关《DTU40P06品牌授权规格书.pdf（8页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、1P-Channel 60 V(D-S)MOSFETFEATURESTrenchFET Power MOSFETMaterial categorization:APPLICATIONSLoad SwitchNotes:a.Duty cycle 1%.b.When mounted on 1 square PCB(FR-4 material).c.See SOA curve for voltage derating.d.Package limited.PRODUCT SUMMARY VDS(V)RDS(on)()ID(A)-600.036 at VGS=-10 V-40d0.045 at VGS=

2、-4.5 V-40dTO-252SGDTop ViewSGDP-Channel MOSFETABSOLUTE MAXIMUM RATINGS(TA=25 C,unless otherwise noted)Parameter SymbolLimitUnitDrain-Source Voltage VDS-60VGate-Source Voltage VGS 20Continuous Drain Current(TJ=175 C)TC=25 CID-40dATC=125 C-27.5Pulsed Drain CurrentIDM-80Avalanche CurrentIAS-30Single Pu

3、lse Avalanche EnergyaL=0.1 mHEAS125mJPower DissipationTC=25 CPD113cWTA=25 C2.5b,cOperating Junction and Storage Temperature Range TJ,Tstg-55 to 150CTHERMAL RESISTANCE RATINGS Parameter Symbol TypicalMaximumUnit Junction-to-Ambientbt 10 sRthJA1518C/WSteady State4050Junction-to-CaseRthJC0.821.1DTU40P0

4、62Notes:a.Pulse test;pulse width 300 s,duty cycle 2%.b.Guaranteed by design,not subject to production testing.c.Independent of operating temperature.Stresses beyond those listed under“Absolute Maximum Ratings”may cause permanent damage to the device.These are stress ratings only,and functional opera

5、tionof the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.Exposure to absolute maximumrating conditions for extended periods may affect device reliability.SPECIFICATIONS(TJ=25 C,unless otherwise noted)ParameterSymbol Te

6、st Conditions Min.Typ.Max.UnitStaticDrain-Source Breakdown VoltageVDSVGS=0 V,ID=-250 A-60VGate Threshold VoltageVGS(th)VDS=VGS,ID=-250 A-1-3Gate-Body LeakageIGSSVDS=0 V,VGS=20 V 100nAZero Gate Voltage Drain CurrentIDSSVDS=-60 V,VGS=0 V-1AVDS=-60 V,VGS=0 V,TJ=125 C-50VDS=-60 V,VGS=0 V,TJ=150 C-100On-

7、State Drain CurrentaID(on)VDS=-5 V,VGS=-10 V-50ADrain-Source On-State ResistanceaRDS(on)VGS=-10 V,ID=-17 A 0.0220.036VGS=-10 V,ID=-40 A,TJ=125 C0.048VGS=-10 V,ID=-40 A,TJ=150 C0.058VGS=-4.5 V,ID=-14 A 0.045Forward Transconductanceagfs VDS=-15 V,ID=-17 A 61SDynamicbInput CapacitanceCissVGS=0 V,VDS=-2

8、5 V,f=1 MHz 4950pFOutput CapacitanceCoss480Reverse Transfer CapacitanceCrss 405Total Gate ChargecQgVDS=-30 V,VGS=-10 V,ID=-40 A 110165nCGate-Source ChargecQgs 19Gate-Drain ChargecQgd 28Turn-On Delay Timectd(on)VDD=-30 V,RL=0.6 ID -40 A,VGEN=-10 V,RG=6 1523nsRise Timectr70105Turn-Off Delay Timectd(of

9、f)175260Fall Timectf175260Source-Drain Diode Ratings and Characteristics TC=25 CbContinuous CurrentIS-40APulsed CurrentISM-80Forward VoltageaVSDIF=-40 A,VGS=0 V-1-1.6VReverse Recovery TimetrrIF=-40 A,dI/dt=100 A/s 4570nsDTU40P063TYPICAL CHARACTERISTICS(25 C,unless otherwise noted)Output Characterist

10、icsTransconductanceCapacitanceVDS -Drain-to-Source Voltage(V)-Drain Current(A)ID3 V01020304050607080012345VGS=10 thru 4 V0204060801000102030405060VGS-Gate-to-Source Voltage(V)-Transconductance(S)gfsTC=-55 C25 C125 C0100020003000400050006000700080000102030405060VDS -Drain-to-Source Voltage(V)C -Capac

11、itance(pF)CissCossCrssTransfer CharacteristicsOn-Resistance vs.Drain CurrentGate Charge010203040506070800.00.51.01.52.02.53.03.54.0VGS -Gate-to-Source Voltage(V)-Drain Current(A)ID25 C-55 CTC=125 C0.0000.0200.0300.0400.0500.06001020304050607080-On-Resistance()ID -Drain Current(A)RDS(on)VGS=10 VVGS=4

12、.5 V0246810020406080100120-Gate-to-Source Voltage(V)Qg -Total Gate Charge(nC)VGSVDS=30 VID=40 ADTU40P064TYPICAL CHARACTERISTICS THERMAL RATINGS(25 C,unless otherwise noted)On-Resistance vs.Junction Temperature0.60.81.01.21.41.61.82.0(Normalized)-On-Resistance TJ -Junction Temperature(C)RDS(on)VGS=10

13、 VID=17 A-50-250255075100125150Source-Drain Diode Forward Voltage0.00.30.60.91.21.5VSD -Source-to-Drain Voltage(V)-Source Current(A)IS100101TJ=25 CTJ=150 CDrain Current vs.Case TemperatureTC-Case Temperature(C)-Drain Current(A)ID0510203040500255075100125150Safe Operating Area1101000.1110100-Drain Cu

14、rrent(A)IDTC=25 CSingle Pulse RDS(on)*Limited byP(t)=0.01P(t)=0.001P(t)=0.0001P(t)=1P(t)=0.1 BVDSS LimitedVDS-Drain-to-Source Voltage(V)*VGS minimum VGSat which RDS(on)is specifiedNormalized Thermal Transient Impedance,Junction-to-CaseSquare Wave Pulse Duration(s)210.10.0110-410-310-210-1Normalized

15、Effective TransientThermal Impedance10.20.10.05Duty Cycle=0.5Single Pulse0.02DTU40P061TO-252AA CASE OUTLINENoteDimension L3 is for reference only.L3DL4L5bb2e1E1D1CA1gage plane height(0.5 mm)eb3EC2ALHMILLIMETERSINCHESDIM.MIN.MAX.MIN.MAX.A2.182.380.0860.094A1-0.127-0.005b0.640.880.0250.035b20.761.140.

16、0300.045b34.955.460.1950.215C0.460.610.0180.024C20.460.890.0180.035D5.976.220.2350.245D15.21-0.205-E6.356.730.2500.265E14.32-0.170-H9.4010.410.3700.410e2.28 BSC0.090 BSCe14.56 BSC0.180 BSCL1.401.780.0550.070L30.891.270.0350.050L4-1.02-0.040L51.141.520.0450.060ECN:X12-0247-Rev.M,24-Dec-12DWG:5347Pack

17、age Information1A P P L I C A T I O N N O T ERECOMMENDED MINIMUM PADS FOR DPAK(TO-252)0.420(10.668)Recommended Minimum PadsDimensions in Inches/(mm)0.224(5.690)0.180(4.572)0.055(1.397)0.243(6.180)0.087(2.202)0.090(2.286)Application Note1DisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJE

18、CT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-Tek”),disclaim any and all liability for any errors,inaccuracies or incompleteness contai

19、ned in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product.To the maximum extent permitted by applicable law,Din-Tek discl

20、aims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warranties,including warranties of fitness for particularpurpose,non-infringement and mercha

21、ntability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applications.Such statements are not binding statementsabout the suitability of products for a par

22、ticular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parametersprovided in datasheets and/or specifications may vary in different applications and perfor

23、mance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise modify Din-Tek s terms and conditions of purchase,including but not limited to the warran

24、ty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of the Din-Tek product could result in personal injury or death.Customers using or selling D

25、in-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to any intellectual

26、property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Material Category PolicyDin-Tek Intertechnology,Inc.hereby certifies that all its products that are identified as RoHS-Compliant fulfill thedef

27、initions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Councilof June 8,2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment(EEE)-recast,unless otherwise specified as non-compliant.Please note that some

28、Din-Tek documentation may still make reference to RoHS Directive 2002/95/EC.We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.Din-Tek Intertechnology,Inc.hereby certifies that all its products that are identified as Halogen-Free fol

29、low Halogen-Freerequirements as per JEDEC JS709A standards.Please note that some Din-Tek documentation may still make referenceto the IEC 61249-2-21 definition.We confirm that all the products identified as being compliant to IEC 61249-2-21conform to JEDEC JS709A standards.Legal Disclaimer NoticeDis

30、claimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-Tek”),disclaim any and all li

31、ability for any errors,inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product.To

32、the maximum extent permitted by applicable law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warranties,including warranties

33、of fitness for particularpurpose,non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applications.Such statements are not b

34、inding statementsabout the suitability of products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parametersprovided in datasheets and/or

35、specifications may vary in different applications and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise modify Din-Tek s terms and co

36、nditions of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of the Din-Tek product could res

37、ult in personal injury or death.Customers using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Legal Disclaimer Notice