WC0801A,深圳市盈达顺科技, WINCOM TECH, 规格书.pdf

《WC0801A,深圳市盈达顺科技, WINCOM TECH, 规格书.pdf》由会员分享，可在线阅读，更多相关《WC0801A,深圳市盈达顺科技, WINCOM TECH, 规格书.pdf（17页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:1/17 Wincom Tech CO.,LTD.The LCD(M)Specialist CONTACT ADDRESS:3F,Block 13,WangJingKeng Industry Park,DaKan XiLi,NanShan,Shenzhen,China.http:/ PART NO.:WC0801A-SFYLYHC06(Side BL)FOR MESSRS.:CONTENTS NO.ITEM PAGE 1.COVER 1 2.RECORD OF REVISION 2 3.GE

2、NERAL SPECIFICATION 3 4.MECHANICAL DATA 3 5.ABSOLUTE MAXIMUM RATINGS 4 6.ELECTRICAL CHARACTERISTICS 5 7.OPTICAL CHARACTERISTICS 5 8.OUTLINE DIMENSION 67 9.BLOCK DIAGRAM 7 10 INTERFACE TIMING CHART 89 11 INSTRUCTION CODE 1011 12 CHARACTER GENERATOR ROM 12 13 SPECIFICATION OF QUALITY ASSURANCE 1317 AC

3、CEPTED BY:PROPOSED BY:Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:2/17 RECORD OF REVISION DATE PAGE SUMMARY 2013-4-1-NEW ISSU Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:3/17 3.General specifications 3.1 General specifications PLEASE REFER TO:“CUSTOMER ACCEPTANCE STANDARD SPECIFICATION

4、S(MS-10-10000)”.3.2 Quality Assurance and Warranty PLEASE REFER TO:“QUALITY ASSURANCE MANUL(MS-10-10001)“.3.3 This individual specification is prior to general specifications 4.Mechanical data Display format:8 characters x 1 line LCD type:STN Positive Yellow-Green,Transflective Backlight color:LED,Y

5、ellow-Green,Side backlight Viewing angle:6:00 Data transfer:8Bit Parallel LCD controller:SPLC780 OR Equivalent(Font:English&Japanese)OP.Voltage:5.0V OP.Temp.:-20+70 Module size:84x 44 x 10.5mm View area:61.0 x 15.8 mm Char size:6.45x 10.75 mm Driving method:1/8 duty,1/4 bias Wincom Tech CO.,LTD.WC08

6、01A-SFYLYHC06(Side BL)PAGE:4/17 5.Absolute maximum ratings 5.1 Electrical absolute maximum ratings I T E M SYMBOL MIN.MAX.UNIT COMMENT INPUT VOLTAGE VI-0.3 6 V-STATIC ELECTRICITY-V VS 0 3.4 Vrms-POWER SUPPLY FOR BACKLIGHT fFL-KHz-5.2 Environmental absolute maximum ratings OPERATING STORAGE I T E M M

7、IN.MAX.MIN.MAX.COMMENT AMBIENT TEMPERATURE-20 70-25 75-HUMIDITY NOTE(2)NOTE(2)NO CONDENSATION VIBRATION NOTE(3)-0.5G-2G 10300Hz XYZ DIRECTIONS 1 Hr EACH SHOCK NOTE(3)-3G-5G 10 msec XYZ DIRECTIONS 1 TIME EACH CORROSIVE GAS NOT ACCEPTABLE NOT ACCEPTABLE-NOTE(2):Ta 50:75%RH MAX.Ta 50:ABSOLUTE HUMIDITY

8、MUST BE LOWER THAN THE HUMIDITY OF 75%RH AT 50.NOTE(3):1G=9.8 m/s2 Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:5/17 6.Electrical characteristics Ta=25 VDD=5.0 V I T E M SYMBOL CONDITION MIN.TYP.MAX.UNIT Power supply voltage for circuit VDD-VSS-4.75 5.0 5.25 V Power supply voltage for LCD driv

9、e VDD-V0-4.5-V VIH H LEVEL 0.7VDD-VDD+0.3 V Data input voltage VIL L LEVEL-0.3-0.2VDD V LCD display duty ratio DUTY-1/16-Ifp I mseo plus 10%Duty cycle -mA Operating voltage 2.8 3.1 3.3 V LED BACKLIGHT Forward current 80 100 mA LED Lifetime-VFL=3.1Vrms fFL=KHz-100,000-Hr LED backlight:Due to the LED

10、backlight working current is XXX Max,and LED chips Vop may be different,Wincom will adjust the backlight resistor according to the LED chips Vop,to meet the brightness maximium.7.Optical characteristics Ta=25 VDD-VO=4.5V I T E M SYMBOL CONDITION MIN.TYP.MAX.UNIT NOTE Viewing angle 2-1 K 2.0-35-20 de

11、g.1 Contrast ratio K =10O =0O 4.0-1 tr(rise)=10O =0O-250 ms 1 Response time(at 25)tf(fall)=10O =0O-250 ms 1 The brightness of backlighting source B VFL=3.1Vrms fFL=KHZ 100-cd/m2 2 NOTE(1):SEE CUSTOMER ACCEPTANCE STANDARD SPECIFICATION FOR DEFINITION OF OPTICAL CHARACTERISTICS NOTE(2):UNDER NORMAL TE

12、MPERATURE AND HUMIDITY IN A DARK ROOM Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:6/17 8.Outline dimension Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:7/17 8.1 Interface Pin Assignment PIN NO.Symbol Leve Function 1 Vss 0V Ground 2 Vdd 5.0V Power Supply for LCM(+)3 V0-Contrast Adjust 4

13、RS H/L Register select signal 5 RW H/L Data read/write 6 E H/L Enable signal 7 DB0 H/L Data bus line 8 DB1 H/L Data bus line 9 DB2 H/L Data bus line 10 DB3 H/L Data bus line 11 DB4 H/L Data bus line 12 DB5 H/L Data bus line 13 DB6 H/L Data bus line 14 DB7 H/L Data bus line 15 K(-)Power supply for LE

14、D BL(-)16 A(+5.0v/30mA)Power supply for LED BL(+)9.Block diagram CONTROLDDLSILED Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:8/17 10.Interface Timing Chart Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:9/17 Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:10/17 11.Instruction Code DISP

15、LAY CHARACTER ADDRESS CODE Display position:1 2 3 4 5 6 7 8 Address line1:00 01 02 03 04 05 06 07 Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:11/17 Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:12/17 12.Character generator ROM Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:13/17 13.S

16、pecification of quality assurance AQL inspection standard Sampling method:MIL-STD-105E,Level II,single sampling Defect classification(Note:*is not including)Classify Item Note AQL Short or open circuit LC leakage Flickering No display Wrong viewing direction 1 Contrast defect(dim,ghost)2 Display sta

17、te Back-light 1,8 Flat cable or pin reverse 10 Major Non-display Wrong or missing component 11 0.65 Background color deviation 2 Black spot and dust 3 Line defect,Scratch 4 Rainbow 5 Chip 6 Display state Pin hole 7 Protruded 12 Polarizer Bubble and foreign material 3 Soldering Poor connection 9 Wire

18、 Poor connection 10 Minor TAB Position,Bonding strength 13 1.0 Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:14/17 Note on defect classification No.Item Criterion Short or open circuit LC leakage Flickering No display Wrong viewing direction 1 Wrong Back-light Not allow Contrast defect 2 Backgr

19、ound color deviation Refer to approval sample 3 Point defect,Black spot,dust(including Polarizer)=(X+Y)/2 Point Size Acceptable Qty.0.10 Disregard 0.100.20 3 0.200.25 2 0.250.30 0 Unit:mm 4 Line defect,Scratch Line Acceptable Qty.L W -0.015W Disregard 3.0L 0.03W 2.0L.05W 2 1.0L 0.1W 1-0.05W Applied

20、as point defect 5 Rainbow Not more than two color changes across the viewing area.Y X L W Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:15/17 NO.Item Criterion 6 Chip Remark:X:Length direction Y:Short direction Z:Thickness direction t:Glass thickness W:Terminal Width Acceptable criterion X Y Z

21、2 0.5mm t/2 Acceptable criterion X Y Z 2 0.5mm t Acceptable criterion X Y Z 3 2 shall not reach to ITO t Acceptable criterion X Y Z Disregard 0.2 t Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:16/17 No.Item Criterion 7 Segment pattern W=Segment width =(X+Y)/2 (1)Pin hole 0.10mm is acceptable.8

22、 Back-light(1)The color of backlight should correspond its specification.(2)Not allow flickering 9 Soldering(1)Not allow heavy dirty and solder ball on PCB.(The size of dirty refer to point and dust defect)(2)Over 50%of lead should be soldered on Land.10 Wire(1)Copper wire should not be rusted(2)Not

23、 allow crack on copper wire connection.(3)Not allow reversing the position of the flat cable.(4)Not allow exposed copper wire inside the flat cable.11*PCB(1)Not allow screw rust or damage.(2)Not allow missing or wrong putting of component.Wincom Tech CO.,LTD.WC0801A-SFYLYHC06(Side BL)PAGE:17/17 NO.I

24、tem Criterion 12 Protruded W:Terminal Width Acceptable criteria:Y 0.4 13 TAB 1.Position W11/3W H11/3H 2 TAB bonding strength test P(=F/TAB bonding width)650gf/cm,(speed rate:1mm/min)5pcs per SOA(shipment)14 Total no.of acceptable Defect A.Zone Maximum 2 minor non-conformities per one unit.Defect distance:each point to be separated over 10mm B.Zone It is acceptable when it is no trouble for quality and assembly in customers end product.