DTS7001品牌授权规格书.pdf

《DTS7001品牌授权规格书.pdf》由会员分享，可在线阅读，更多相关《DTS7001品牌授权规格书.pdf（8页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、P-Channel 60 V(D-S)MOSFETFEATURESHalogen-free According to IEC 61249-2-21DefinitionTrenchFET Power MOSFETHigh-Side SwitchingLow On-Resistance:5 Low Threshold:-2 V(typ.)Fast Swtiching Speed:20 ns(typ.)Low Input Capacitance:20 pF(typ.)1200 V ESD ProtectionCompliant to RoHS Directive 2002/95/ECAPPLICAT

2、IONSDrivers:Relays,Solenoids,Lamps,Hammers,Display,Memories,Transistors,etc.Battery Operated SystemsPower Supply Converter CircuitsSolid-State RelaysBENEFITSEase in Driving SwitchesLow Offset(Error)VoltageLow-Voltage OperationHigh-Speed CircuitsEasily Driven without BufferNotes:a.Surface mounted on

3、FR4 board.b.Pulse width limited by maximum junction temperature.PRODUCT SUMMARY VDS(V)RDS(on)()VGS(th)(V)ID(mA)-605 at VGS=-10 V-1 to-3-130ABSOLUTE MAXIMUM RATINGS TA=25 C,unless otherwise noted Parameter SymbolLimit UnitDrain-Source Voltage VDS-60VGate-Source Voltage VGS 20Continuous Drain Currenta

4、TA=25 CID-130mATA=100 C-105Pulsed Drain CurrentbIDM-800Power DissipationaTA=25 CPD350mWTA=100 C140Maximum Junction-to-AmbientaRthJA350C/WOperating Junction and Storage Temperature RangeTJ,Tstg-55 to 150CSGDP-Channel MOSFETG TO-236(SOT-23)S D Top View 2 3 1 DTS?011 DTS7001Notes:a.Pulse test:PW 300 s

5、duty cycle 2%.b.Switching time is essentially independent of operating temperature.Stresses beyond those listed under“Absolute Maximum Ratings”may cause permanent damage to the device.These are stress ratings only,and functional operationof the device at these or any other conditions beyond those in

6、dicated in the operational sections of the specifications is not implied.Exposure to absolute maximumrating conditions for extended periods may affect device reliability.SPECIFICATIONS TA=25 C,unless otherwise notedParameterSymbol Test Conditions LimitsUnit Min.Typ.aMax.StaticDrain-Source Breakdown

7、VoltageVDSVGS=0 V,ID=-10 A-60VGate-Threshold VoltageVGS(th)VDS=VGS,ID=-250 A-1-3Gate-Body LeakageIGSS VDS=0 V,VGS=20 V 10AVDS=0 V,VGS=10 V 200nAVDS=0 V,VGS=10 V,TJ=85 C 500VDS=0 V,VGS=5 V 100Zero Gate Voltage Drain CurrentIDSS VDS=-60 V,VGS=0 V-25VDS=-60 V,VGS=0 V,TJ=85 C-250On-State Drain CurrentaI

8、D(on)VGS=-10 V,VDS=-4.5 V-50mAVGS=-10 V,VDS=-10 V-600Drain-Source On-ResistanceaRDS(on)VGS=-4.5 V,ID=-25 mA10VGS=-10 V,ID=-500 mA5VGS=-10 V,ID=-500 mA,TJ=125 C 9Forward TransconductanceagfsVDS=-10 V,ID=-100 mA 80mSDiode Forward VoltageVSDIS=-200 mA,VGS=0 V -1.4VDynamicTotal Gate ChargeQgVDS=-30 V,VG

9、S=-15 VID -500 mA1.7nCGate-Source ChargeQgs0.26Gate-Drain ChargeQgd0.46Input CapacitanceCissVDS=-25 V,VGS=0 Vf=1 MHz23pFOutput CapacitanceCoss10Reverse Transfer CapacitanceCrss5SwitchingbTurn-On Timetd(on)VDD=-25 V,RL=150 ID -200 mA,VGEN=-10 V,Rg=10 20nsTurn-Off Timetd(off)352 DTS7001TYPICAL CHARACT

10、ERISTICS 25 C,unless otherwise notedOutput CharacteristicsOn-Resistance vs.Drain CurrentGate Charge0.00.20.40.60.81.0012345VDS-Drain-to-Source Voltage(V)-Drain Current(A)IDVGS=10 V5 V4 V6 V7 V8 V04812162002004006008001000ID -Drain Current(mA)VGS=4.5 VVGS=10 V-On-Resistance()RDS(on)VGS=5 V036912150.0

11、0.30.60.91.21.51.8ID=500 mA-Gate-to-Source Voltage(V)Qg-Total Gate Charge(nC)VGSVDS=30 VVDS=48 VTransfer CharacteristicsCapacitanceOn-Resistance vs.Junction Temperature030060090012000246810VGS-Gate-to-Source Voltage(V)-Drain Current(mA)IDTJ=-55 C 125 C25 C08162432400510152025VDS-Drain-to-Source Volt

12、age(V)C-Capacitance(pF)CrssCossCissVGS=0 V0.00.30.60.91.21.51.8-50-250255075100125150TJ-Junction Temperature(C)VGS=10 V at 500 mAVGS=4.5 V at 25 mA RDS(on)-On-Resistance(Normalized)3 DTS7001.Source-Drain Diode Forward VoltageThreshold Voltage Variance Over Temperature1.21.5110010000.000.30.60.9TJ=25

13、 CTJ=125 CVSD-Source-to-Drain Voltage(V)-Source Current(A)IS10TJ=-55 C VGS=0 V-0.3-0.2-0.1-0.00.10.20.30.40.5-50-250255075100125150VGS(th)Variance(V)ID=250 A TJ-Junction Temperature(C)On-Resistance vs.Gate-Source VoltageSingle Pulse Power,Junction-to-Ambient02468100246810VGS-Gate-to-Source Voltage(V

14、)ID=500 mAID=200 mARDS(on)-On-Resistance()0.01012.531006000.1Power(W)Time(s)1.520.5110TA=25 C Normalized Thermal Transient Impedance,Junction-to-Ambient10-310-200601110-110-4100210.10.010.20.10.050.02Single PulseDuty Cycle=0.5Square Wave Pulse Duration(s)Normalized Effective TransientThermal Impedan

15、ce1.Duty Cycle,D=2.Per Unit Base=RthJA=350 C/W3.TJM-TA=PDMZthJA(t)t1t2t1t2Notes:4.Surface MountedPDM THERMAL RATINGS(TA=25 C,unless otherwise noted)4 DTS70011SOT-23(TO-236):3-LEADbEE1132See1DA2AA1CSeating Plane0.10 mm0.004CCL1LqGauge PlaneSeating Plane0.25 mmDimMILLIMETERS INCHES Min Max Min Max A0.

16、891.120.0350.044A10.010.100.00040.004A20.881.020.03460.040b0.350.500.0140.020c0.0850.180.0030.007D2.803.040.1100.120E2.102.640.0830.104E11.201.400.0470.055e0.95 BSC0.0374 Refe11.90 BSC0.0748 RefL0.400.600.0160.024L10.64 Ref0.025 RefS0.50 Ref0.020 Refq3838ECN:S-03946-Rev.K,09-Jul-01DWG:5479Package In

17、formation?1A P P L I C A T I O N N O T ERECOMMENDED MINIMUM PADS FOR SOT-230.106(2.692)Recommended Minimum PadsDimensions in Inches/(mm)0.022(0.559)0.049(1.245)0.029(0.724)0.037(0.950)0.053(1.341)0.097(2.459)Return to IndexReturn to IndexApplication Note1DisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS

18、AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-Tek”),disclaim any and all liability for any errors,inaccuracies or inc

19、ompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product.To the maximum extent permitted by applicable

20、 law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warranties,including warranties of fitness for particularpurpose,non-infri

21、ngement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applications.Such statements are not binding statementsabout the suitability of

22、products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parametersprovided in datasheets and/or specifications may vary in different appli

23、cations and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise modify Din-Tek s terms and conditions of purchase,including but not lim

24、ited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of the Din-Tek product could result in personal injury or death.Customers

25、using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to

26、 any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Material Category PolicyDin-Tek Intertechnology,Inc.hereby certifies that all its products that are identified as RoHS-Compli

27、ant fulfill thedefinitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Councilof June 8,2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment(EEE)-recast,unless otherwise specified as non-compliant.Plea

28、se note that some Din-Tek documentation may still make reference to RoHS Directive 2002/95/EC.We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.Din-Tek Intertechnology,Inc.hereby certifies that all its products that are identified a

29、s Halogen-Free follow Halogen-Freerequirements as per JEDEC JS709A standards.Please note that some Din-Tek documentation may still make referenceto the IEC 61249-2-21 definition.We confirm that all the products identified as being compliant to IEC 61249-2-21conform to JEDEC JS709A standards.Legal Di

30、sclaimer NoticeDisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-Tek”),discl

31、aim any and all liability for any errors,inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production

32、of any product.To the maximum extent permitted by applicable law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warranties,inc

33、luding warranties of fitness for particularpurpose,non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applications.Such st

34、atements are not binding statementsabout the suitability of products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parametersprovided in

35、datasheets and/or specifications may vary in different applications and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise modify Din-

36、Tek s terms and conditions of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of the Din-Tek

37、 product could result in personal injury or death.Customers using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Legal Disclaimer Notice