DTU19P10品牌授权规格书.pdf

《DTU19P10品牌授权规格书.pdf》由会员分享，可在线阅读，更多相关《DTU19P10品牌授权规格书.pdf（9页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、1P-Channel 100 V(D-S)MOSFETFEATURESHalogen-free According to IEC 61249-2-21DefinitionTrenchFET Power MOSFET100%Rg and UIS TestedCompliant to RoHS Directive 2002/95/ECAPPLICATIONSPower SwitchDC/DC ConvertersPRODUCT SUMMARY VDS(V)RDS(on)()ID(A)Qg(Typ.)-1000.195 at VGS=-10 V-1911.70.210 at VGS=-4.5 V-1

2、7TO-252SGDTop ViewDrain Connected to TabSGDP-Channel MOSFETNotes:a.Duty cycle 1%.b.See SOA curve for voltage derating.c.When Mounted on 1 square PCB(FR-4 material).ABSOLUTE MAXIMUM RATINGS TC=25 C,unless otherwise notedParameter SymbolLimitUnitDrain-Source Voltage VDS-100VGate-Source Voltage VGS 20C

3、ontinuous Drain Current(TJ=150 C)TC=25 CID-19ATC=70 C-12.1Pulsed Drain CurrentIDM-45Avalanche CurrentIAS-18Single Avalanche EnergyaL=0.1 mHEAS16.2mJMaximum Power DissipationaTC=25 CPD32.1bWTA=25 Cc2.5Operating Junction and Storage Temperature Range TJ,Tstg-55 to 150CTHERMAL RESISTANCE RATINGS Parame

4、ter SymbolLimitUnitJunction-to-Ambient(PCB Mount)cRthJA50C/WJunction-to-Case(Drain)RthJC3.9DTU19P102Notes:a.Pulse test;pulse width 300 s,duty cycle 2%.b.Guaranteed by design,not subject to production testing.c.Independent of operating temperature.Stresses beyond those listed under“Absolute Maximum R

5、atings”may cause permanent damage to the device.These are stress ratings only,and functional operationof the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.Exposure to absolute maximumrating conditions for extended peri

6、ods may affect device reliability.SPECIFICATIONS TJ=25 C,unless otherwise notedParameterSymbol Test Conditions Min.Typ.Max.UnitStaticDrain-Source Breakdown VoltageVDSVDS=0 V,ID=-250 A-100VGate Threshold VoltageVGS(th)VDS=VGS,ID=-250 A-1-2.5Gate-Body LeakageIGSSVDS=0 V,VGS=20 V 250nAZero Gate Voltage

7、 Drain CurrentIDSSVDS=-100 V,VGS=0 V-1AVDS=-100 V,VGS=0 V,TJ=125 C-50VDS=-100 V,VGS=0 V,TJ=150 C-250On-State Drain CurrentaID(on)VDS -10 V,VGS=-10 V-15ADrain-Source On-State ResistanceaRDS(on)VGS=-10 V,ID=-3.6 A 0.1620.195VGS=-4.5 V,ID=-3.4 A0.1750.210Forward Transconductanceagfs VDS=-15 V,ID=-3.6 A

8、 12SDynamicbInput CapacitanceCissVGS=0 V,VDS=-50 V,f=1 MHz 1055pFOutput CapacitanceCoss65Reverse Transfer CapacitanceCrss 41Total Gate ChargecQgVDS=-50 V,VGS=-10 V,ID=-3.6 A 23.234.8nCVDS=-50 V,VGS=-4.5 V,ID=-3.6 A11.717.6Gate-Source ChargecQgs 3.5Gate-Drain ChargecQgd 4.8Gate ResistanceRgf=1 MHz1.2

9、5.711.5Turn-On Delay Timectd(on)VDD=-50 V,RL=17.2 ID -2.9 A,VGEN=-10 V,Rg=1 714nsRise Timectr1218Turn-Off Delay Timectd(off)3350Fall Timectf918Drain-Source Body Diode Ratings and Characteristics TC=25 CbContinuous CurrentIS-19APulsed CurrentISM-45Forward VoltageaVSDIF=-2.9 A,VGS=0 V-0.8-1.5VReverse

10、Recovery TimetrrIF=-2.9 A,dI/dt=100 A/s 5075nsPeak Reverse Recovery CurrentIRM(REC)-4-6AReverse Recovery ChargeQrr98147nCDTU19P103TYPICAL CHARACTERISTICS 25 C,unless otherwise notedOutput CharacteristicsTransfer Characteristics Transconductance0369121501234VGS=10 V thru 5 VVGS=4 VVDS-Drain-to-Source

11、 Voltage(V)-Drain Current(A)IDVGS=3 V0.00.40.81.21.62.001234TC=25 CTC=125 CTC=-55 CVGS-Gate-to-Source Voltage(V)-Drain Current(A)ID051015202503691319ID-Drain Current(A)-Transconductance(S)gfsTC=125 CTC=-55 CTC=25 COn-Resistance vs.Drain CurrentOn-Resistance vs.Gate-to-Source VoltageGate Charge0.100.

12、150.200.250.3003691319VGS=4.5 VVGS=10 V-On-Resistance()RDS(on)ID-Drain Current(A)0.000.150.300.450.600246810TJ=25 CTJ=150 C-On-Resistance()RDS(on)VGS-Gate-to-Source Voltage(V)02468100510152025VDS=80 VID=3.6 AVDS=50 VVDS=25 V-Gate-to-Source Voltage(V)Qg-Total Gate Charge(nC)VGSDTU19P104TYPICAL CHARAC

13、TERISTICS 25 C,unless otherwise notedSource-Drain Diode Forward VoltageCapacitanceOn-Resistance vs.Junction Temperature0.11101000.00.30.60.91.2TJ=25 CTJ=150 CVSD-Source-to-Drain Voltage(V)-Source Current(A)ISCrss040080012001600020406080100CissCossVDS-Drain-to-Source Voltage(V)C-Capacitance(pF)0.50.9

14、1.31.72.1-50-250255075100125150ID=3.6 AVGS=4.5 VVGS=10 VTJ-Junction Temperature(C)(Normalized)-On-ResistanceRDS(on)Threshold VoltageDrain Source Breakdown vs.Junction Temperature Current Derating-2.3-2.0-1.7-1.4-1.1-50-250255075100125150ID=250 A(V)VGS(th)TJ-Temperature(C)-130-124-118-112-106-100-50-

15、250255075100125150ID=250 AVDS-Drain-to-Source Voltage(V)TJ-Junction Temperature(C)02468100255075100125150TC-Case Temperature(C)ID-Drain Current(A)DTU19P105TYPICAL CHARACTERISTICS 25 C,unless otherwise noted Single Pulse Avalanche Current Capability vs.Time110100Time(s)IDAV(A)TJ=150 CTJ=25 C10-310-21

16、0-110-410-610-5Safe Operating Area10010.11101000.01190.1TA=25 CSingle Pulse100 msLimited by RDS(on)*BVDSS Limited1 ms100 s10 ms1 s,10 s,DCVDS-Drain-to-Source Voltage(V)*VGS minimum VGSat which RDS(on)is specified-Drain Current(A)IDNormalized Thermal Transient Impedance,Junction-to-Case10-310-201110-

17、110-40.20.1Duty Cycle=0.5Square Wave Pulse Duration(s)Normalized Effective TransientThermal Impedance10.10.05Single Pulse0.02DTU19P10 1TO-252AA CASE OUTLINENoteDimension L3 is for reference only.L3DL4L5bb2e1E1D1CA1gage plane height(0.5 mm)eb3EC2ALHMILLIMETERSINCHESDIM.MIN.MAX.MIN.MAX.A2.182.380.0860

18、.094A1-0.127-0.005b0.640.880.0250.035b20.761.140.0300.045b34.955.460.1950.215C0.460.610.0180.024C20.460.890.0180.035D5.976.220.2350.245D15.21-0.205-E6.356.730.2500.265E14.32-0.170-H9.4010.410.3700.410e2.28 BSC0.090 BSCe14.56 BSC0.180 BSCL1.401.780.0550.070L30.891.270.0350.050L4-1.02-0.040L51.141.520

19、.0450.060ECN:X12-0247-Rev.M,24-Dec-12DWG:5347Package Information 1A P P L I C A T I O N N O T ERECOMMENDED MINIMUM PADS FOR DPAK(TO-252)0.420(10.668)Recommended Minimum PadsDimensions in Inches/(mm)0.224(5.690)0.180(4.572)0.055(1.397)0.243(6.180)0.087(2.202)0.090(2.286)Application Note 1DisclaimerAL

20、L PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-Tek”),disclaim any and all liability f

21、or any errors,inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing production of any product.To the maxim

22、um extent permitted by applicable law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warranties,including warranties of fitnes

23、s for particularpurpose,non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applications.Such statements are not binding st

24、atementsabout the suitability of products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parametersprovided in datasheets and/or specifica

25、tions may vary in different applications and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise modify Din-Tek s terms and conditions

26、of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of the Din-Tek product could result in pe

27、rsonal injury or death.Customers using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or im

28、plied,by estoppel or otherwise,to any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Material Category PolicyDin-Tek Intertechnology,Inc.hereby certifies that all its products t

29、hat are identified as RoHS-Compliant fulfill thedefinitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Councilof June 8,2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment(EEE)-recast,unless otherwis

30、e specified as non-compliant.Please note that some Din-Tek documentation may still make reference to RoHS Directive 2002/95/EC.We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.Din-Tek Intertechnology,Inc.hereby certifies that all i

31、ts products that are identified as Halogen-Free follow Halogen-Freerequirements as per JEDEC JS709A standards.Please note that some Din-Tek documentation may still make referenceto the IEC 61249-2-21 definition.We confirm that all the products identified as being compliant to IEC 61249-2-21conform t

32、o JEDEC JS709A standards.Legal Disclaimer NoticeDisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their beh

33、alf(collectively,“Din-Tek”),disclaim any and all liability for any errors,inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular pur

34、pose orthe continuing production of any product.To the maximum extent permitted by applicable law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)a

35、ny and all implied warranties,including warranties of fitness for particularpurpose,non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek product

36、s in generic applications.Such statements are not binding statementsabout the suitability of products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular a

37、pplication.Parametersprovided in datasheets and/or specifications may vary in different applications and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do no

38、t expand or otherwise modify Din-Tek s terms and conditions of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in

39、 which the failure of the Din-Tek product could result in personal injury or death.Customers using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Legal Disclaimer Notice