BSOB模式与BBOS模式学习.pptx

《BSOB模式与BBOS模式学习.pptx》由会员分享，可在线阅读，更多相关《BSOB模式与BBOS模式学习.pptx（27页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、1Bond Stick On Ball(BSOB)/Bond Ball On Stitch(BBOS)/Tail Break第1页/共27页21.0)BOND STICK ON BALL(BSOB)1.1)DescriptionThis bonding process is specially developed by ASM to handle multi-die(MCM)bonding application.In the conventional approach,if one is trying to connect the gold wire from one die to the

2、another,a capillary mark of second bond will be evident on top of the die which may damage the die.The BSOB process will solve this problem by bonding a ball onto the dies surface first,followed by bonding another wire where the second bonds wedge will be landing on top of this bonded ball(figure 1)

3、.第2页/共27页3Die 1Die 2Bond Ball2nd Bond(wedge)1st Bond Figure 1:Bond Stick On Ball(BSOB)第3页/共27页42.0)BOND BALL ON STITCH(BBOS)/SECURITY BOND2.1)DescriptionThis process is also known as security bond.It bonds a ball on top of the wedge of the normal connection wire.This process is mainly used to secure

4、 the second bond sticking capability.(Figure 2)Die 1LeadBond Ball2nd Bond(wedge)1st Bond Figure 2:Bond Ball On Stitch(BBOS)第4页/共27页53.1)Free Air Ball(FAB 2)is aligned to the center of the bond pad on device 2.Device 1Device 2FAB 23.0 STANDOFF BALL CONTROL BONDING SEQUENCE第5页/共27页63.2)Capillary desce

5、nds and bonds ball to bond pad.Device 1Device 2W/clamp openCapillaryApplication of 1st bond stand off ball parameter to form Ball Thickness and Ball SizeDuring Stand Off Bonding,SOB parameters are applied.第6页/共27页73.3)Capillary rises to loop base to clear ball.Device 1Device 2W/clamp openCapillary r

6、ises to set Loop BaseLoop BaseContact Pt.Loop base is the distance between the capillary tip and contact point.Recommended setting=2第7页/共27页83.4)Capillary move to programme ball offset.Ball offset can be programmed towards or away from the first bond.+ve towards 2nd bond -ve away 2nd bond Device 1De

7、vice 2W/clamp openActual Ball Offset=Setting x 10umIf Ball Offset Setting=22Then Actual Loop Base=220umRecommended Setting=-ve 35第8页/共27页93.5)Capillary descends and forms stitch bond on top of the ball.Device 1Device 2W/clamp open*Ball ThicknessSOB Parameter (Stand Off Ball Parameter)Capillary desce

8、nds to set Ball Thickness(Amt.Z movement above the ball height)Contact Pt.*Ball Thickness is the distance between the capillary tip and contact point Recommended setting=2 第9页/共27页103.6)Capillary moves horizontally for a scrub distance to weaken the wire at ball neck.Device 1Device 2W/clamp openScru

9、b one direction away from ballActual Scrub Distance=Setting x 0.8 umIf Scrub Distance Setting=10Then Actual Scrub Distance=8 um Capillary move to set Scrub Distance One direction ONLY-Away from the ball Recommended setting=8第10页/共27页113.7)Capillary rises to tail heightDevice 1Device 2W/clamp closeCa

10、pillary moves to set Tail Length(Amount Z movement above the bump before the wire clamp closes)Recommended setting=35第11页/共27页123.8)Capillary rises and tears the wire,as BH ascend to Fire Level.Device 1Device 2W/c close第12页/共27页133.9)EFO fires to form free air ball.Cycle repeats until all“Standoff B

11、all”are placed.Device 1Device 2Bond BallFAB第13页/共27页143.10)After placing all standoff balls.The machine continue to bond wires.2nd Bond(wedge)1st Bond Device1Device2Device1Bond Ball第14页/共27页15Bump ball formation for BSOB/BBOSMOTION BO LB BT SCNormalLBBOBTScrubFlatLBBOBTScrub=0CONELBBOBT=LBScrub=0 LB

12、 BO BT LB BOThe bump ball formation process is almost like bonding a normal wire,including 1st bond,looping and 2nd bond parameters.第15页/共27页164.0)PARAMETER DEFINITION IN STAND OFF BALL CONTROL MENU4.1)Loop BaseThis parameter determines the loop level of the bondhead which should be sufficient to av

13、oid the ball.Range:Loop Base 0 5Setting:24.2)Ball OffsetThis setting controls the distance of the table move in order to offset the capillary from the standoff ball.Negative value can be moved towards to the first bond.Positive value can be moved away from the first bond.Range:Ball Offset -40 20Sett

14、ing:-ve 35 第16页/共27页174.4)Scrub DistanceThis setting controls the capillary moves horizontally with a Scrub amplitude to weaken the wire at neck.It is always away from thefirst bond.Range:Scrub Dist 4 12Setting:84.5)Tail LengthThis setting controls the length of the tail where the bondhead rises to

15、the preset height before the wire clamp is closed.Range:Tail Length 30 40Setting:354.3)Ball ThicknessThis parameter refer to the ball thickness which controls the level of the bondhead as it descends to the top of the ballRange:Ball Thickness 0 5Setting:2第17页/共27页184.6)Time Base 1/2This setting cont

16、rols the bond time applied to the standoff ball control only.Time 1 for the 1st bond and Time 2 for the 2nd bond.4.7)Power Base 1/2This setting controls the ultrasonic power applied to the standoff ball control only.Power 1 for the 1st bond and Time 2 for the 2nd bond.4.8)Force Base 1/2This setting

17、controls the bonding force applied to the standoff ball control only.Force 1 for the 1st bond and Force 2 for the 2nd bond.第18页/共27页194.9)Standby Power 1/2This setting controls the power activated when the bonding head reach the search level,to the moment the bond head contacts the bond surface.With

18、 the vibration,before contact take place.Bond head will clean up the pad surface and remove water vapor on the pad.This parameter used for the standoff ball control only.4.10)Contact Time 1/2Refer to the Contact time 1/2 definition in Bond Parameter menu.But this parameter will be affected on the St

19、andoff ball control only.第19页/共27页204.11)Contact Power 1/2Refer to the Contact Power 1/2 definition in Bond Parameter menu.But this parameter will be affected on the Standoff ball control only.4.12)Contact Force 1/2Refer to the Contact Force 1/2 definition in Bond Parameter menu.But this parameter w

20、ill be affected on the Standoff ball control only.第20页/共27页21Figure 4:Standoff Ball Control Parameter Display(page 2)5.0 BSOB WIRE PARAMETERS第21页/共27页225.1)Wire Offset In-MenuThis is the offset parameter that is required to ensure maximum contact area between the stitch bond and ball.It is always aw

21、ay from the first bond.Range:Wire Offset 10 30 Recommended setting=255.2)Second Bond Search SpeedThis Parameter controls the impact for stitch on ball.Range:Search Speed 2 32 256Recommended setting=322nd Bond WedgeStand Off BallCapillary position during stitch bond第22页/共27页235.3)Time Base 1/2This se

22、tting controls the bond time applied to the device.Time 1 for the 1st bond and Time 2 for the 2nd bond.5.4)Power Base 1/2This setting controls the ultrasonic power applied to the device.Power 1 for the 1st bond and Time 2 for the 2nd bond.5.5)Force Base 1/2This setting controls the bonding force app

23、lied to the device.Force 1 for the 1st bond and Force 2 for the 2nd bond.第23页/共27页24Ball Parameters for BSOB and BBOS5.6 Tail LengthControls the length of the tail where the bond head rises to the preset height before the wire clamp is closedRange 15 45(*10um)第24页/共27页25Ball Parameters for BSOB and

24、BBOS5.7 Tail break TimeUsed to increase the wire straightness and reduce the snake wire during BSOB/BBOS applicationRange 0 -100(*0.25ms)Setting 10第25页/共27页26Ball Parameters for BSOB and BBOS5.8 Tail Break DistanceUsed together with the tail break timeTraveling distance can be determined by the settingRange 10 50(*10um)Setting 25Tail break time and tail break distance are valid only when the wire or ball tail break map in wire parameter menu is set to“Y”.第26页/共27页27感谢您的观看。第27页/共27页