C级产品外观检验标准V.pdf

《C级产品外观检验标准V.pdf》由会员分享，可在线阅读，更多相关《C级产品外观检验标准V.pdf（5页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、1.0CV01 规范A级产品（含出口CD-ROM）光碟外观检验标准，确保成品符合产品质量要求。2.0 适用范围：本公司生产的所有光碟产品之生产及检验各环节。3.0 检验环境及人员要求：3.1 温湿度：按生产车间环境要求。（252，70下列）3.2 检验人员要求：无色盲、色弱，经上岗考核合格；3.3 亮度：在通常日光灯照明下，避免强光反射；3.4 角度：受检面与检验者视线成45度角；3.5 距离：将产品放置于距离检验者眼睛30cm处，使光线均匀从光盘面反射到眼睛；3.6 检查方法：产品从左到右认真目测一次。4.0 缺陷分类：4.1轻微(Minor)：不影响使用，轻微影响外观或者客户能够同意的缺陷

2、 4.2重要(Major)：非致命缺陷，不可能影响使用功能，但客户难以同意的缺陷 5.0 检验工具：目测 6.0 检验标准：Visual Criteria for Disc/光盘外观（目测）标准 Label Printing Defect 印刷不良 正常标准 Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 1 Smear 化墨正面检测，观看 秒发现该缺陷 -图案,字体Not easy to see the defect from front view-picutres,words 碟边阔度mmdisc

3、 edge-width 1mm 轻微(Minor)D1 2 Ink spot,splash 漏墨 穿网,碟边渍墨正面检测，观看 秒发现该缺陷 -图案,字体Not easy to see the defect from front view-picutres,words 阔度 1mmwidth 1 轻微(Minor)3 Ink in middle ring 中圈墨渍正面检测，观看 秒发现该缺陷Not easy to see the defect from front view 正面观看墨渍不显眼及放于白纸上墨渍少于圆周Not easy to see the defect from front v

4、iew,ink shorter than 1/2 of centre diameter 轻微(Minor)4 Registration 走位/套字正面检测，观看 秒发现该缺陷 -图案,字体Not easy to see the defect from front view-picutres,words 阔度width 0.5mm 轻微(Minor)5 Wordings 字体清晰度不可令图案、字体不能辨认pictures and words must clearly recognize 不可令字样不清-阔度 0.5 mmpictures and words must clearly recogn

5、ize-width 0.5 mm 轻微(Minor)6 Printing eccentricity 印刷偏心两边印刷与碟边之相差 的平均值1mm The average of the two distance differences between the image edge and disc edge 1 mm 两边印刷与碟边之相差 的平均值1mmThe average of the two distance differences between the image edge and disc edge 1 mm 轻微(Minor)Visual Criteria for Disc/光盘外

6、观（目测）标准 Label Printing Defect 印刷不良 正常标准 Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 7 Incomplete printing,missing ink 塞网 缺划露银正面检测，观看 秒发现该缺陷 不可令字体不能辨认Not easy to see the defect from front view,words must clearly recognize 直径 1 mm 及少于 5 点 及不可令字体不能辨认Not easy to see the defect

7、 from front view,words must clearly recognize 轻微(Minor)8 Stain 渍正面检测，观看 秒发现该缺陷 不可令字体不能辨认Not easy to see the defect from front view,words must clearly recognize 直径 1 mm 及 少于 5 点 及长度 4 mmdiameter 1 mm,less than 5 points,length 4 mm 轻微(Minor)9 Dust 尘N/A N/A 阔度 1 mm,长度3mm,少于 5点width 1mm,length 2mm 轻微(Mi

8、nor)D1 10 Color uneven 颜色不平均正面检测，两碟相并颜色差别轻微color deviation not easy to recognize from the front view 色差仪 重要(Major)11 1.1 Color variation compare with pantone 颜色与pantone 不符正面检测，两碟相并颜色差别轻微color deviation not easy to recognize from the front view 色差仪 重要(Major)12 水渍正面检测，轻微发现该缺陷 Not easy to see the defec

9、t from front view 正面不明显 阔度 5 cm,长度5cmNot easy to see the defect from front view,width 4cm,length 4cm 轻微(Minor)Visual Criteria for Disc/光盘外观（目测）标准 Label Printing Defect 印刷不良 正常标准 Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 13 水印 线痕正面检测，轻微发现该缺陷 -图案Not easy to see the defect

10、from front view -picture 正面看不明显 长度1cm,少于5条 Not easy to see the defect from front view,length 1cm,less than 5 lines 轻微(Minor)14 线纹正面检测，轻微发现该缺陷 -图案Not easy to see the defect from front view -picture 正面不明显 阔度 1 mm,长度2cm,少于 5条Not easy to see the defect from front view,width 1mm,length 2cm,less than 5 li

11、nes 轻微(Minor)15 Printing scratch 印刷刮花 正面检测，轻微发现该缺陷功能测试为合格 Not easy to see the defect from front view Functional test PASS 正面不明显及长度 2mm及少于 5条 及 功能测试为合格 Not easy to see the defect from the front view,length 2mm,less than 5 lines,Functional test PASS 重要(Major)16 Scratch on the information side 碟面刮花 正面检

12、测，轻微发现该缺陷功能测试为合格 Not easy to see the defect from front view Functional test PASS 正面不明显及长度 2mm及少于 5条 及 功能测试为合格 Not easy to see the defect from the front view,length 2mm,less than 5 lines,Functional test PASS 重要(Major)17 Missing print 漏印 绝对不同意 Not acceptable 绝对不同意 Not acceptable 重要(Major)Lacquer Defec

13、t 沥架不良 正常标准 Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 1 Lacquer spot 沥架点不明显影响光碟图案外观 Not affect the picture visually 直径 1mm,少于 5 点diameter 1mm,less than 5 points 轻微(Minor)D1 2 Radial vein 太阳纹不明显影响光碟图案外观Not affect the picture visually 不明显影响光碟图案外观Not affect the picture visu

14、ally 轻微(Minor)Visual Criteria for Disc/光盘外观（目测）标准 Lacquer Defect 沥架不良 正常标准 Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 3 Suction cup mark/Lacquer mark 吸盘印、机械手的手指印 沥架印正面检测，轻微发现该缺陷 Not easy to see the defect from front view 阔度 1mm,长度4mmwidth 0.5mm,length 4mm 轻微(Minor)不平均沥架边沥

15、架纹不明显影响光碟图案外观Not affect the picture visually 阔度 1 mm,长度1 mmwidth 1mm,length 1mm 轻微(Minor)Sputtering Layer Defect 电镀层不良 正常标准 Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 1 Pin Hole 穿洞 含溅镀针孔正面检测，轻微发现该缺陷 功能测试为合格Not easy to see the defect from front view Functional test PASS 阔度

16、 0.5 mm 功能测试为合格width 0.5 mm Functional test PASS 重要(Major)2 Dent 缺口正面检测，轻微发现该缺陷 功能测试为合格Not easy to see the defect from front view Functional test PASS 阔度 1 mm 功能测试为合格width 1 mm Functional test PASS 重要(Major)3 Sputtering layer eccentricity 溅镀层偏心两边电镀层与碟边之相差的平均值1mm The average of the two distance diffe

17、rences between the sputtering layer edge and disc edge 1 mm 两边电镀层与碟边之相差的平均值1mm The average of the two distance differences between the sputtering layer edge and disc edge 1 mm 轻微(Minor)Injection Defect 注塑不良 正常标准 Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 1 Flow mark,Silve

18、r steak 气纹、流痕以不入该光碟内容位置为同意Accept if not in program area 以不入该光碟内容位置为同意Accept if not in program area 重要(Major)2 Cloud 云影（水纹）正面检测，轻微发现该缺陷 Not easy to see the defect from front view 正面观看不明显Not easy to see the defect from front view 轻微(Minor)Visual Criteria for Disc/光盘外观（目测）标准 Injection Defect 注塑不良 正常标准

19、Normal standard limit 特殊标准(C+)Special standard limit 分类 Classification 3 3.1 Bump 凹/凸点（尘点、凸包）正面检测，轻微发现该缺陷 功能测试为合格Not easy to see the defect from front view Functional test PASS 正面检测，轻微发现该缺陷 功能测试为合格Not easy to see the defect from front view Functional test PASS 重要(Major)4 4.1 Scratches,surface defect

20、(from Leybold)刮花(含溅镀刮花)以不入该光碟内容位置为同意Accept if not in program area 以不入该光碟内容位置为同意Accept if not in program area 重要(Major)5 5.1 Cold line 冷胶功能测试为合格Functional test PASS 功能测试为合格Functional test PASS 重要(Major)6 6.1 Reflective spot/black spot 黑点 反光点正面观看轻微功能测试为合格Not easy to see the defect from front view Func

21、tional test PASS 正面观看轻微功能测试为合格Not easy to see the defect from front view Functional test PASS 重要(Major)7 7.1 Glue bubble (DVD only)胶水气泡只供正面观看轻微功能测试为合格Not easy to see the defect from front view Functional test PASS 正面观看轻微功能测试为合格Not easy to see the defect from front view Functional test PASS 重要(Major)编写 黄国雄 批准 黄国雄 日期 2008-10-01