STBLWHC06,深圳市盈达顺科技, WINCOM TECH, 规格书.pdf

《STBLWHC06,深圳市盈达顺科技, WINCOM TECH, 规格书.pdf》由会员分享，可在线阅读，更多相关《STBLWHC06,深圳市盈达顺科技, WINCOM TECH, 规格书.pdf（17页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:1/17 Wincom Tech CO.,LTD.The LCD(M)Specialist CONTACT ADDRESS:3F,Block 13,WangJingKeng Industrial Park,DaKan XiLi，NanShan,Shenzhen City,China.http:/ PART NO.:WC1602E V3.0-STBLWHC06 FOR MESSRS.:CONTENTS NO.ITEM PAGE 1.COVER 1 2.RECORD OF REVISION 2 3.G

2、ENERAL SPECIFICATION 3 4.MECHANICAL DATA 3 5.ABSOLUTE MAXIMUM RATINGS 4 6.ELECTRICAL CHARACTERISTICS 5 7.OPTICAL CHARACTERISTICS 5 8.OUTLINE DIMENSION 67 9.BLOCK DIAGRAM 7 10 INTERFACE TIMING CHART 89 11 INSTRUCTION CODE 1011 12 CHARACTER GENERATOR ROM 12 13 SPECIFICATION OF QUALITY ASSURANCE 1317 A

3、CCEPTED BY:PROPOSED BY:Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:2/17 RECORD OF REVISION DATE PAGE SUMMARY 2011-6-9-NEW SPEC 2014-4-21 RF resistor from 91K to 75K Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:3/17 3.General specifications 3.1 General specifications PLEASE REFER TO:“CUSTOMER

4、ACCEPTANCE STANDARD SPECIFICATIONS(MS-10-10000)”.3.2 Quality Assurance and Warranty PLEASE REFER TO:“QUALITY ASSURANCE MANUL(MS-10-10001)“.3.3 This individual specification is prior to general specifications 4.Mechanical data Display format:16 characters x 2 lines Microprocessor interface:8 bits Par

5、allel LCD type:STN Negative,Blue Backlight color:White,LED Viewing angle:6 oclock LCD controller:SPLC780 or Equivalent Module size:85x 29.5 x 11.4 mm View area:64 x16 mm Dot size:0.66x 0.56 mm Dot pitch:0.70 x 0.60mm Driving method:1/16 duty,1/5 bias Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:4

6、/17 5.Absolute maximum ratings 5.1 Electrical absolute maximum ratings I T E M SYMBOL MIN.MAX.UNIT COMMENT POWER SUPPLY FOR LOGIC VDD-VSS-0.3 6 V-INPUT VOLTAGE VI VSS VDD V-STATIC ELECTRICITY-V VS 0 3.3 Vrms-POWER SUPPLY FOR BACKLIGHT fFL-KHz-Vrms Ta=25 STARTING VOLTAGE FOR BACKLIGHT-Vrms Ta=25 POWE

7、R SUPPLY FOR LCD VDD-V0-4.7 V-5.2 Environmental absolute maximum ratings OPERATING STORAGE I T E M MIN.MAX.MIN.MAX.COMMENT AMBIENT TEMPERATURE-20 70-30 80-HUMIDITY NOTE(2)NOTE(2)NO CONDENSATION VIBRATION NOTE(3)-0.5G-2G 10300Hz XYZ DIRECTIONS 1 Hr EACH SHOCK NOTE(3)-3G-5G 10 msec XYZ DIRECTIONS 1 TI

8、ME EACH CORROSIVE GAS NOT ACCEPTABLE NOT ACCEPTABLE-NOTE(2):Ta 70:75%RH MAX.Ta 70:ABSOLUTE HUMIDITY MUST BE LOWER THAN THE HUMIDITY OF 75%RH AT 70.NOTE(3):1G=9.8 m/s2 Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:5/17 6.Electrical characteristics Ta=25 VDD=5.0 V I T E M SYMBOL CONDITION MIN.TYP.MA

9、X.UNIT Power supply voltage for circuit VDD-VSS-4.75 5.0 5.25 V Power supply voltage for LCD drive VDD-V0-4.7-V LCD display duty ratio DUTY-1/16-Ifp I mseo plus 10%Dutg cyele -mA Operating voltage-3.0 3.3 V LED BACKLIGHT Forward current 30 40 mA LED Lifetime-VFL=3.0Vrms fFL=KHz-100,000-Hr Power supp

10、ly LCD current IEE VDD-V0=4.7 V-mA LED backlight:Due to the LED backlight working current is XXX Max,and LED chips Vop may be different,Wincom will adjust the backlight resistor according to the LED chips Vop,to meet the brightness maximum 7.Optical characteristics Ta=25 VDD-V0=4.7V I I I I T T T T

11、E E E E M M M M SYMBOLSYMBOLSYMBOLSYMBOL CONDITIONCONDITIONCONDITIONCONDITION MIN.MIN.MIN.MIN.TYPTYPTYPTYP.MAX.MAX.MAX.MAX.UNITUNITUNITUNIT NOTENOTENOTENOTE Viewing angle 2-1 K 2.0-35-20 deg.1 Contrast ratio K =10O =0O 4.0-1 tr(rise)=10O =0O-250 ms 1 Response time(at 25)tf(fall)=10O =0O-250 ms 1 The

12、 brightness of backlighting source B VFL=3.0Vrms fFL=KHZ-250-cd/m2 2 NOTE(1):SEE CUSTOMER ACCEPTANCE STANDARD SPECIFICATION FOR DEFINITION OF OPTICAL CHARACTERISTICS NOTE(2):UNDER NORMAL TEMPERATURE AND HUMIDITY IN A DARK ROOM Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:6/17 8.Outline dimension

13、Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:7/17 8.1 Interface Pin Assignment PIN NO.Symbol Leve Function 1 VDD 5.0V Power supply voltage for LCM(+)2 Vss 0V Ground 3 V0-Contrast Adjust 4 RS H/L Register select signal 5 R/W H/L Data read/write 6 E H/L Enable signal 7 DB0 H/L Data bus line 8 DB1 H

14、/L Data bus line 9 DB2 H/L Data bus line 10 DB3 H/L Data bus line 11 DB4 H/L Data bus line 12 DB5 H/L Data bus line 13 DB6 H/L Data bus line 14 DB7 H/L Data bus line A A(+3.0V/30mA)Power supply for LED BL(+)K K(-)Power supply for LED BL(-)9.Block diagram CONTROLDDLSILEDSPLC780 Wincom Tech CO.,LTD.WC

15、1602E V3.0-STBLWHC06 PAGE:8/17 10.Interface Timing Chart Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:9/17 11.Instruction Code Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:10/17 DISPLAY CHARACTER ADDRESS CODE Display position:1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Address line1:00 01 02 03 04

16、05 06 07 08 09 0A 0B 0C 0D 0E 0F Address line2:40 41 42 43 44 45 46 47 48 49 4A 4B BC 4D 4E 4F Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:11/17 12.Character generator ROM Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:12/17 13.Specification of quality assurance Wincom Tech CO.,LTD.WC1602E V3.0

17、-STBLWHC06 PAGE:13/17 AQL inspection standard Sampling method:MIL-STD-105E,Level II,single sampling Defect classification(Note:*is not including)Classify Item Note AQL Short or open circuit LC leakage Flickering No display Wrong viewing direction 1 Contrast defect(dim,ghost)2 Display state Back-ligh

18、t 1,8 Flat cable or pin reverse 10 Major Non-display Wrong or missing component 11 0.65 Background color deviation 2 Black spot and dust 3 Line defect,Scratch 4 Rainbow 5 Chip 6 Display state Pin hole 7 Protruded 12 Polarizer Bubble and foreign material 3 Soldering Poor connection 9 Wire Poor connec

19、tion 10 Minor TAB Position,Bonding strength 13 1.0 Note on defect classification Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:14/17 No.Item Criterion Short or open circuit LC leakage Flickering No display Wrong viewing direction 1 Wrong Back-light Not allow Contrast defect 2 Background color devi

20、ation Refer to approval sample 3 Point defect,Black spot,dust(including Polarizer)=(X+Y)/2 Point Size Acceptable Qty.0.10 Disregard 0.100.20 3 0.200.25 2 0.250.30 0 Unit:mm 4 Line defect,Scratch Line Acceptable Qty.L W -0.015W Disregard 3.0L 0.03W 2.0L.05W 2 1.0L 0.1W 1-0.05W Applied as point defect

21、 5 Rainbow Not more than two color changes across the viewing area.NO.Item Criterion Y X L W Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:15/17 6 Chip Remark:X:Length direction Y:Short direction Z:Thickness direction t:Glass thickness W:Terminal Width Acceptable criterion X Y Z 2 0.5mm t/2 Accept

22、able criterion X Y Z 2 0.5mm t Acceptable criterion X Y Z 3 2 shall not reach to ITO t Acceptable criterion X Y Z Disregard 0.2 t No.Item Criterion Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:16/17 7 Segment pattern W=Segment width =(X+Y)/2 (1)Pin hole 0.10mm is acceptable.8 Back-light(1)The col

23、or of backlight should correspond its specification.(2)Not allow flickering 9 Soldering(1)Not allow heavy dirty and solder ball on PCB.(The size of dirty refer to point and dust defect)(2)Over 50%of lead should be soldered on Land.10 Wire(1)Copper wire should not be rusted(2)Not allow crack on coppe

24、r wire connection.(3)Not allow reversing the position of the flat cable.(4)Not allow exposed copper wire inside the flat cable.11*PCB(1)Not allow screw rust or damage.(2)Not allow missing or wrong putting of component.NO.Item Criterion Wincom Tech CO.,LTD.WC1602E V3.0-STBLWHC06 PAGE:17/17 12 Protrud

25、ed W:Terminal Width Acceptable criteria:Y 0.4 13 TAB 1.Position W11/3W H11/3H 2 TAB bonding strength test P(=F/TAB bonding width)650gf/cm,(speed rate:1mm/min)5pcs per SOA(shipment)14 Total no.of acceptable Defect A.Zone Maximum 2 minor non-conformities per one unit.Defect distance:each point to be separated over 10mm B.Zone It is acceptable when it is no trouble for quality and assembly in customers end product.