标准对应互换表.xls

《标准对应互换表.xls》由会员分享，可在线阅读，更多相关《标准对应互换表.xls（14页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、序号德国标准中文品名英文品名ItemDIN-StandardDescription in ChineseDesciption in English1DIN1圆锥销Taper pins2DIN7圆柱销Parallel pins3DIN84开槽圆柱头螺钉Slotted cheese head screws4DIN85开槽盘头螺钉Slotted pan head screws5DIN93单耳止动垫圈Tab washers6DIN94开口销Split cooter pins7DIN95开槽半沉头木螺钉Slotted raised csk head wood screws8DIN96开槽半圆头木螺钉Sl

2、otted round head wood screws9DIN97开槽沉头木螺钉Slotted countersunk head wood screws10DIN125-A平垫Plain washers11DIN125-B平垫（带倒角）Mediun washers12DIN126平垫Plain washers13DIN127-A重型弹垫Spring lock washers,tang ends14DIN127-B标准弹垫Spring lock washers,square ends15DIN128-A鞍形弹垫Single coil spring lock washers16DIN137-A弹

3、簧止动垫圈Curved spring washers17DIN137-B波形弹垫Wave spring washers18DIN186T 型方颈螺栓T-head blots with square neck19DIN188T 型双接头螺栓T-head bolts with double nip20DIN258螺纹圆锥销Taper pins with threaded end21DIN261T 型头螺栓T-head bolts22DIN315AF蝶型螺母（美制）Wing nuts America form23DIN315DF蝶型螺母（德制）Wing nuts germany form24DIN3

4、16AF蝶型螺母（美制）Wing screws America form25DIN317DF蝶型螺母（德制）Wing screws germany form26DIN319圆球型盖型螺母Ball knobs27DIN404开槽带孔球面Slotted capstan screws圆柱头蚴钉28DIN417开槽长圆柱端Slotted set srews with full dog point紧定螺钉29DIN427开槽平端Slotted set srews with chamfered end紧定螺钉（半牙）30DIN431小六角特薄细牙Pip nuts with thread螺母31DIN432

5、外舌止动垫圈External tap32DIN433小垫圈Washers for cheese head screws(用于圆柱头螺钉)33DIN434方斜垫圈（U 型）Square taper washers forU-section34DIN435方斜垫圈（I 型）Square taper washers forI-sections35DIN436方垫圈Square washers36DIN438开槽凹端紧定螺钉Slotted set with cup point37DIN439六角薄螺母Hexagon thin nuts38DIN439细牙六角薄螺母Hexagon thin nuts39

6、DIN440木螺钉专用垫圈Rounds washers for wood constructions40DIN443密封帽Sealing caps,push-in type41DIN444活节螺栓 B 型Eye bolts form B42DIN462内舌止动垫圈Internal tab washers43DIN463双耳止动垫圈Washers with two taps44DIN464滚花高头螺钉Knurled thumb screws with collar45DIN465开槽滚花高头螺钉Slotted knurled thumb screws with collar46DIN466滚花高

7、螺母Knurled thumb nuts with collar47DIN467滚花薄螺母Knurled thumb thin nuts48DIN470锁紧垫圈Sealing washers49DIN471轴用弹性垫圈Retaining rings forshafts(external),circlips50DIN472孔用弹性垫圈Retaining rings for bores(internal),circlips51DIN478方头带垫螺栓Square head bolts with collar52DIN479方头圆柱底端螺栓Square head bolts with half do

8、g point53DIN480方头带垫关圆底端Square head bolts with collar,half dog point螺栓54DIN508T 型槽螺母T-slot nuts55DIN525单头螺柱Single end studs56DIN529地脚螺栓Masonry bolts57DIN546带槽圆螺母Slotted round nuts58DIN547端面带孔圆螺母Round nuts with drilled holes in one face59DIN551开槽平端紧定螺钉Slotted set screws with flat point60DIN553开槽锥端紧定螺钉

9、Slotted set screws with cone point61DIN555六角螺母Hexagon nuts62DIN557方螺母-CSquare nuts63DIN558六角头螺钉Hexagon screws64DIN561六角头圆柱端Hexagon set screws with full dog point紧定螺钉65DIN562薄型方螺母-BSquare nuts without bevel(pressed nuts)66DIN571六角头木螺钉Hexgon head wood screw(coach screws)67DIN580吊环螺钉Lifting eye bolts68

10、DIN582吊环螺母Lifting eye nuts69DIN601六角头螺栓Hexagon blots33DIN434方斜垫圈（U 型）70DIN603大半圆头方颈螺栓（马车螺栓）Mushroom head square neck bolts(carriagebolts)71DIN604沉头带插销马车Flat countersunk nib bolts螺栓72DIN605沉头长方颈马车Flat countersunk long squareneck bolts螺栓73DIN607半圆头带插销马车螺栓Cup head nib bolts74DIN608沉头短方颈马车Flat countersu

11、nk short square neck bolts螺栓75DIN609六角头精配螺栓Hexagon fitted bolts,long thread（长螺纹）76DIN610六角头精配螺栓Hexagon fitted bolts short thread（短螺栓）77DIN653滚花平头螺钉Knurled thumb screws thin type78DIN660半圆头铆钉Round head rivets79DIN661沉头铆钉Contersunk head rivets80DIN662半 沉头铆钉Raised contersunk head rivets81DIN674大扁头铆钉Mus

12、hroom head rivets82DIN703重型侧面带孔圆螺母Adjusting rings,heavy range(shaftingcollars)83DIN705侧面带孔圆螺母Adjusting rings,light range(shaftingcollars)84DIN741卡头Wire rope clips85DIN787T 型槽螺钉T-slot screws86DIN835双头螺柱Studs-metal(end=2d)（牙长=2D）87DIN906内六角锥型闭锁Hexagon socket pipe plugs,conical thread螺钉88DIN908内六角直型闭锁T

13、hread螺钉89DIN909外六角锥型闭锁Thread螺钉90DIN910外六角直型闭锁Hexagon head screw plugs,cyl.thread螺钉91DIN911内六角扳手Socket wrenches92DIN912内六角圆柱头螺钉Hexagon socket cap screws93DIN913内六角平端紧定Hexagon socket set screws with falt point螺钉94DIN914内六角尖端紧定Hexagon socket set screws with cone point螺钉95DIN915内六角圆柱端紧定螺钉Hexagon socket

14、set screws with dog point96DIN916内六角凹端紧定螺钉Hexagon socket set screws with cup point97DIN917薄型盲螺母Hexagon cap nuts98DIN920开槽小圆柱头螺钉Slotted short cheese head screws99DIN921开槽大圆柱头螺钉Slotted large cheese head screws100DIN923开槽圆柱头轴肩Slotted pan head screw with shoulder螺钉101DIN927开槽无头轴肩螺钉Slotted shoulder screw

15、s102DIN928焊接方螺母Square weld nuts103DIN929焊接六角螺母Hexagon weld nuts104DIN931六角头螺栓Hexagon head screws（全牙）105DIN933六角头螺栓Hexagon head screws（半牙）106DIN934六角头螺母（1 型）Hexagon full nuts107DIN934细牙六角头螺母（1 型）Hexagon full nuts108DIN935开槽六角螺母Hexagon slotted and castle nuts109DIN936六角头薄螺母Hexagon thin nuts110DIN937六角

16、头开槽薄螺母Hexagon thin slotted and caslte nuts111DIN938双头螺距Studs metal(end=1d)（牙长=1D）112DIN939双头螺距Studs metal(end=1.25d)（牙长=1.5D）113DIN940双头螺距Studs metal(end=1.5d)（牙长=1.25D）114DIN960六角头细牙螺栓Hexagon head bolts,metric fine pitch thread（全牙）115DIN961六角头细牙螺栓Hexagon head bolts,metric fine pitch thread（半牙）116DI

17、N962头部穿孔六角头Additional shapes and versions for bolts螺栓117DIN963开槽沉头螺钉Slotted countersund head screws118DIN964开槽半沉头螺钉Slotted raised countersunk oval head screws119DIN965十字槽沉头螺钉Cross recessed countersunk head screws120DIN966十字槽半沉头螺钉Cross recessed raisedCountersunk head screws121DIN970六角头螺母Hexagon nuts

18、type-1122DIN971六角头螺母Hexagon nuts type-2123DIN972细牙六角头螺母（2 型）Hexagon nuts with fine thread124DIN975牙条（全螺纹）Threaded rods(studdings)125DIN976螺纹销Threaded pins(stud bolts)126DIN979六角头开槽薄螺母（2 型）Hexagon thin slotted and castle nuts127DIN980全金属六角锁紧螺母（1 型）Prevaillng rorque type hexagon nuts,allmetal nuts128D

19、IN981圆螺母Locknuts129DIN982六角头尼龙锁紧螺母Prevailing rorque type hexagon nuts,heavytype,with nylon130DIN985六角头薄型尼龙锁紧螺母Prevalling torque type hoxagon nuts,heavytype,with nylon131DIN986六角盖型尼龙锁紧螺母Preailling torque typedomed capnuts withnylon insert132DIN988配合垫片Shim rings133DIN1052木材连接用垫片Washers for timber conn

20、ectors134DIN1151沉头钢钉Round plain head nails135DIN1440销钉专用垫片 A 型Plain washers for clevis pins(A 型)136DIN1441销钉专用垫片Plain washers for clevis pins137DIN1444带头销钉Clevis pins with head138DIN1471圆锥型槽销Grooved pins,taper grooved139DIN1472圆锥型槽销Grooved pins,taper grooved half length（半槽）140DIN1473平行槽销Grooved pins

21、,parallel grooved full length（带倒角）141DIN1474前端凹槽槽销Grooved pins,reverve grooved half length142DIN1475中部凹槽槽销Grooved pins,center grooved143DIN1476圆头槽销Grooved pins with round head144DIN1477沉头槽销Grooved pins with countersunk head145DIN1479六角螺母棒Turnuckles(center parts),made out of hexagonbar146DIN1480花蓝螺栓T

22、urnuckles with eye bolt and hook bolt147DIN1481弹性圆柱销Spring pins,heavy type148DIN1587组合式盖型螺母Hexagon domed cap nuts149DIN1804开槽圆螺母Slotted round nuts for hook spammer(配合沟头扳手)150DIN1816圆螺母（带插销孔）Round nuts with set holes151DIN2093盘型弹簧垫圈Disc springs152DIN3017喉箍Hose clamps153DIN3404润滑油嘴Lubricating nipples,

23、button head（旋扭头）154DIN3567管夹Shackles for conduilts155DIN3570U 型螺栓Stirrup bolts(U-bolts)156DIN6319球面垫圈Spherical washers,conical seats157DIN6325圆柱销Parallel pins158DIN6330厚六角螺母Hexagon nuts,1.5d159DIN6331厚六角法兰面Hexagon nuts,1.5d with collar螺母160DIN6334长六角螺母Hexagon nuts,3d161DIN6797-A外齿锁紧垫圈External teeth

24、lock washers162DIN6797-I内齿锁紧垫圈Internal teeth lock washers163DIN6798-A外锯齿锁紧垫圈External teeth serrated lock washers164DIN6798-I内锯齿锁紧垫圈Internal teeth serrated lock washers165DIN6799开口挡圈Retaining rings for shafts(E-rings),circlips166DIN6885平键（A 型）Parallel keys(form A)167DIN6888半圆键Woodruff keys168DIN6899嵌

25、环（支撑环）Thimbles169DIN6900机器螺钉和垫圈Screws and washers assemblies组合件170DIN6901自攻螺钉和垫圈Tapping screws and washer assemblies组合件171DIN6912薄型带孔Hexagon cocket head cap screws with hole,lowhead内六角圆柱螺钉172DIN6914大六角头螺栓Hexagon head bolts with large head(friction grip nolts)173DIN6915大六角螺母Hexagon nuts with large wi

26、deth across flat(friction grip nuts)174DIN6916大垫圈Round washers for friction grip bolts175DIN6917楔型方垫圈Spuare taper washers for friction grip boltson T-176DIN6923六角法兰面螺母Hexagon flange nuts177DIN6925全金属六角锁紧螺母（2 型）Prevailing torque type hexagon nuts,allmetallic nuts181DIN7346轻型弹性圆柱销Spring pins,light typ

27、e182DIN7349重型弹性圆柱Washers for bolts with heavy type springpinss销用垫圈183DIN7500ISO 公制螺纹螺钉（多种头型）Thread forming screws for ISO-metric thread184DIN7504自攻自钻螺钉Self-drilling tapping screws（多种头型）185DIN7513开槽切削螺纹螺钉（多种头型）Thread cutting screws186DIN7516十字槽切削螺纹螺钉（多种头型）Thread cutting screws cross recess187DIN7965T

28、 型四爪螺母Tee nuts with pronge188DIN7968钢结构用六角头螺栓连接副Hexagon head fitted bolts for steelstructures189DIN7971开槽盘头Pan head tapping screws with slot自攻螺钉190DIN7972开槽沉头countersunk flat head tapping screws withslot自攻螺钉191DIN7973开槽半沉头Raised sountersunk oval head tapping screwswith slot自攻螺钉192DIN7976六角头自攻螺钉Hexag

29、on tapping screws193DIN7980圆柱头螺钉用Spring lock washers for screws withcylindrical heads弹簧垫圈194DIN7981十字槽盘头Pan head tapping screws with cross recessed自攻螺攻195DIN7982十字槽沉头Countersunk flat head tapping screws withcross recessed自攻螺攻196DIN7983十字槽半沉头Raised countersunk oval head tapping screwswith cross自攻螺攻19

30、7DIN7984薄型内六角Hexagon socket head cap screws with,reducedhead圆柱头螺钉198DIN7985十字槽盘头螺钉Pan head screws with cross recessed199DIN7989钢结构用垫圈Washers for steel structures,200DIN7990钢结构用Hexagon head bolts for steel structures六角头螺栓201DIN7991内六角沉头螺钉Hexagon socket coutersunk head screws202DIN7993轴用钢丝挡圈Roundwire

31、snap rings for shafts203DIN7995十字槽半沉头Cross recessed raised countersunk head woodscrews木螺钉204DIN7996十字槽圆头Cross recessed round head wood screws木螺钉205DIN7997十字槽沉头Cross recessed countersunk head wood screws木螺钉206DIN8140螺纹护套Ciol inserts,coarse,fine thread,silf locking(普通、自锁等)207DIN9021大外径垫圈Washers,outsid

32、e diameter appro.3d208DIN11024弹簧卡子sping cotter for a bolt209DIN13257平板螺栓Belting bolts(elevator bolts)210DIN18182干壁钉Dry wall screws（墙板钉）211DIN28129环型螺母Lifting nuts(eye nuts)212DIN70952圆螺母用止退Tab washer for slotted round nuts垫圈197DIN7984Hexagon socket head cap screws with,reducedhead国际标准中国标准ISO-Standar

33、dGB-StandardISO2339GB117ISO2339GB119-86ISO1207GB65-85ISO1580GB67-85GB854ISO1234GB91GB101GB99GB100ISO7089GB97.1-85ISO7090GB97.2-85ISO7091GB7244GB93-87GB7245-87GB955GB37-88ISO8737GB62-88GB832-88ISO7435GB75-85ISO2342GB73-85GB808-88GB856-88ISO7092GB848-95GB852-88GB852-88ISO7436GB74-85ISO4035GB6172-86ISO

34、8675GB6173-86ISO7094GB798-88GB855-88GB834-88GB806-88GB807-88GB893-86GB893.86ISO299GB799-88GB817-76GB815-88ISO4776GB73-85ISO7434GB71-85ISO4034GB39-88ISO4018GB102-86ISO3266GB825-76ISO4016GB852-88ISO8677GB14-88GB835-88ISO1051GB867-86ISO1051GB869-86ISO1051ISO1051GB816-88ISO299GB900-88ISO2936ISO4762GB70-

35、85ISO4026GB77-85ISO4027GB78-85ISO4028GB79-85ISO4029GB80-85GB838-88GB830-88GB/T13680-92GB/T13681-92ISO4014GB5782-86ISO4017GB5783-86ISO4032GB6170-86ISO8673GB6171-86ISO7035GB6178-86ISO4035GB6172.1-86ISO7038GB6181-86GB897-88GB898-88ISO8765GB5785-86ISO8676GB8786-86ISO2009GB68-85ISO2010GB69-85ISO7046GB819

36、-85ISO7047GB820-85ISO8674GB6176-86GB15389-94ISO7199GB6184-86ISO2982GB812-88ISO7040GB889.1-86ISO10511GB6172.2-86ISO8738ISO2341ISO8744GB/T13829.2ISO8745GB/T13829.2ISO8740ISO8741ISO8742ISO8746ISO8747ISO8752GB879-86GB802-88GB849-88ISO8734GB56-88GB6177-86GB862.1-87GB861.1-87GB862.2-87GB861.2-87GB896-76IS

37、O773/2491ISO3912GB9074.1-17GB9074.18-23ISO4161GB6187-86ISO7042GB6185.1-2000ISO13337GB1228/1229/1230ISO1481GB5282-85ISO1482GB5283-85ISO1483GB5284-85ISO1479GB5285-85ISO8738ISO7049GB845-85ISO7050GB846-85ISO7051GB847-86ISO7045GB818-85GB1230-84GB1229-84ISO10642GB895.2-86GB952-86GB950-86GB951-86ISO7093GB96-85GB63-88GB/858-88