PCB_深圳市盈达顺科技有限公司 WINCOM TECH, 规格书.pdf

《PCB_深圳市盈达顺科技有限公司 WINCOM TECH, 规格书.pdf》由会员分享，可在线阅读，更多相关《PCB_深圳市盈达顺科技有限公司 WINCOM TECH, 规格书.pdf（15页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:1/15 Wincom Tech CO.,LTD.The LCD(M)Specialist CONTACT ADDRESS:3F,Block 13,Wang Jing Keng Industrial Park,DaKan,XiLi,NanShan,Shenzhen City,China.http:/ PART NO.:WO12864-GC-01-SFYLYHC06(with PCB)FOR MESSRS.:CONTENTS NO.ITEM PAGE 1.COVER 1 2.RE

2、CORD OF REVISION 2 3.GENERAL SPECIFICATION 3 4.MECHANICAL DATA 3 5.ABSOLUTE MAXIMUM RATINGS 4 6.ELECTRICAL CHARACTERISTICS 5 7.OPTICAL CHARACTERISTICS 5 8.OUTLINE DIMENSION 67 9.BLOCK DIAGRAM 7 10 INTERFACE TIMING CHART 8-9 11 INSTRUCTION CODE 10 12 SPECIFICATION OF QUALITY ASSURANCE 1115 ACCEPTED B

3、Y:PROPOSED BY:Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:2/15 RECORD OF REVISION DATE PAGE SUMMARY 2012-4-27-NEW ISSUE Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:3/15 3.General specifications 3.1 General specifications PLEASE REFER TO:“CUSTOMER ACCEPTANCE STANDARD SPECI

4、FICATIONS(MS-10-10000)”.3.2 Quality Assurance and Warranty PLEASE REFER TO:“QUALITY ASSURANCE MANUL(MS-10-10001)“.3.3 This individual specifiction is prior to general specifications 4.Mechanical data Display format:128 x 64 DOTS LCD type:COG,STN Positive Yellow-Green,Transflective Backlight color:LE

5、D,Yellow-Green Viewing angle:6:00 Data transfer:8Bit Parallel LCD controller:ST7565R OR Equivalent Module size:93.7 x 53.2 x 5.8mm View area:70.7 x 38.8 mm Dot size:0.48 x 0.48 mm Dot pitch:0.52 x 0.52mm Driving method:1/65duty,1/9 bias Warning：Dont clean the LCD or Backlight by liquid!Wincom Tech.C

6、O.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:4/15 5.Absolute maximum ratings 5.1 Electrical absolute maximum ratings I T E M SYMBOL MIN.MAX.UNIT COMMENT POWER SUPPLY FOR LOGIC VDD-VSS-0.3 3.6 V-INPUT VOLTAGE VI VSS VDD V-STATIC ELECTRICITY-V-VS-0.3 2.3 Vrms-POWER SUPPLY FOR BACKLIGHT fFL-KHz-Vrms Ta

7、=25 STARTING VOLTAGE FOR BACKLIGHT-Vrms Ta=25 POWER SUPPLY FOR LCD Vlcd-9.0 V-.5.2 Environmental absolute maximum ratings OPERATING STORAGE I T E M MIN.MAX.MIN.MAX.COMMENT AMBIENT TEMPERATURE-20 70-30 80-HUMIDITY NOTE(2)NOTE(2)NO CONDENSATION VIBRATION NOTE(3)-0.5G-2G 10300Hz XYZ DIRECTIONS 1 Hr EAC

8、H SHOCK NOTE(3)-3G-5G 10 msec XYZ DIRECTIONS 1 TIME EACH CORROSIVE GAS NOT ACCEPTABLE NOT ACCEPTABLE-NOTE(2):Ta 70:75%RH MAX.Ta 0:ABSOLUTE HUMIDITY MUST BE LOWER THAN THE HUMIDITY OF 75%RH AT 70.NOTE(3):1G=9.8 m/s2 Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:5/15 6.Electrical character

9、istics Ta=25 VDD=3.3V I T E M SYMBOL CONDITION MIN.TYP.MAX.UNIT Power supply voltage for circuit VDD-VSS-3.0 3.3 3.4 V Power supply voltage for LCD drive VDD-VEE-9.0-V VIH H LEVEL 2.4-VDD V Data input voltage VIL L LEVEL-0.3-0.4 V LCD display duty ratio DUTY-1/64-Ifp I mseo plus 10%Dutg cyele -mA Op

10、erating voltage 1.9 2.1 2.2 V LED BACKLIGHT Forward current 60 70 mA LED Lifetime-VFL=2.1Vrms fFL=KHz-100,000-Hr NOTE:LED backlight:Due to the LED backlight working current is XXX Max,and LED chips Vop may be different,Wincom will adjust the backlight resistor according to the LED chips Vop,to meet

11、the brightness maximium.7.Optical characteristics Ta=25 VLCD=9.0V I I I I T T T T E E E E M M M M SYMBOLSYMBOLSYMBOLSYMBOL CONDITIONCONDITIONCONDITIONCONDITION MIN.MIN.MIN.MIN.TYPTYPTYPTYP.MAX.MAX.MAX.MAX.UNITUNITUNITUNIT NOTENOTENOTENOTE Viewing angle 2-1 K 2.0-35-20 deg.1 Contrast ratio K =10O =0O

12、 4.0-1 tr(rise)=10O =0O-250 ms 1 Response time(at 25)tf(fall)=10O =0O-250 ms 1 The brightness of backlighting source B VFL=2.1Vrms fFL=KHZ-50-cd/m2 2 NOTE(1):SEE CUSTOMER ACCEPTANCE STANDARD SPECIFICATION FOR DEFINITION OF OPTICAL CHARACTERISTICS NOTE(2):UNDER NORMAL TEMPERATURE AND HUMIDITY IN A DA

13、RK ROOM Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:6/15 8.Outline dimension 接触面补强板DOTS:128*64 Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:7/15 8.2 Interface Pin Assignment PIN NO.Symbol Leve Function 1/CS 5.0V Chip Selection Signal (Active Low)2/RES 0V Reset(Active Low)3

14、 A0 H/L Register select signal 4 WR H/L Data write 5 RD H/L Data read 6 DB0 H/L Data Bus Line 7 DB1 H/L Data Bus Line 8 DB2 H/L Data Bus Line 9 DB3 H/L Data Bus Line 10 DB4 H/L Data Bus Line 11 DB5 H/L Data Bus Line 12 DB6 H/L Data Bus Line 13 DB7 H/L Data Bus Line 14 VDD 3.3V Power supply for logic

15、 circuit 15 VSS 0V Ground 16 VOUT +10V Output Voltage for LCD Driving 17 CAP3+-For DC/DC voltage converter 18 CAP1-For DC/DC voltage converter 19 CAP1+-For DC/DC voltage converter 20 CAP2+-For DC/DC voltage converter 21 CAP2-For DC/DC voltage converter 22 V4-Power supply for the liquid crystal drive

16、 23 V3-Power supply for the liquid crystal drive 24 V2-Power supply for the liquid crystal drive 25 V1-Power supply for the liquid crystal drive 26 V0-Power supply for the liquid crystal drive Red wire A 2.1V/60mA Power supply for BL LED(+)Black wire K 0V Power supply for BL LED(-)9 Block diagram Wi

17、ncom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:8/15 10.Interface Timing Chart Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:9/15 Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:10/15 11.Instruction Code IC Specification:Please refer to http:/ Wincom Tech.CO.,LTD.WO1286

18、4-GC-01-SFYLYHC06(with PCB)PAGE:11/15 12.Specification of quality assurance AQL inspection standard Sampling method:MIL-STD-105E,Level II,single sampling Defect classification(Note:*is not including)Classify Item Note AQL Short or open circuit LC leakage Flickering No display Wrong viewing direction

19、 1 Contrast defect(dim,ghost)2 Display state Back-light 1,8 Flat cable or pin reverse 10 Major Non-display Wrong or missing component 11 0.65 Background color deviation 2 Black spot and dust 3 Line defect,Scratch 4 Rainbow 5 Chip 6 Display state Pin hole 7 Protruded 12 Polarizer Bubble and foreign m

20、aterial 3 Soldering Poor connection 9 Wire Poor connection 10 Minor TAB Position,Bonding strength 13 1.0 Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:12/15 Note on defect classification No.Item Criterion Short or open circuit LC leakage Flickering No display Wrong viewing direction 1 Wr

21、ong Back-light Not allow Contrast defect 2 Background color deviation Refer to approval sample 3 Point defect,Black spot,dust(including Polarizer)=(X+Y)/2 Point Size Acceptable Qty.0.10 Disregard 0.100.20 3 0.200.25 2 0.250.30 0 Unit:mm 4 Line defect,Scratch Line Acceptable Qty.L W -0.015W Disregard

22、 3.0L 0.03W 2.0L.05W 2 1.0L 0.1W 1-0.05W Applied as point defect 5 Rainbow Not more than two color changes across the viewing area.Y X L W Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:13/15 NO.Item Criterion 6 Chip Remark:X:Length direction Y:Short direction Z:Thickness direction t:Glas

23、s thickness W:Terminal Width Acceptable criterion X Y Z 2 0.5mm t/2 Acceptable criterion X Y Z 2 0.5mm t Acceptable criterion X Y Z 3 2 shall not reach to ITO t Acceptable criterion X Y Z Disregard 0.2 t Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:14/15 No.Item Criterion 7 Segment patt

24、ern W=Segment width =(X+Y)/2 (1)Pin hole 0.10mm is acceptable.8 Back-light(1)The color of backlight should correspond its specification.(2)Not allow flickering 9 Soldering(1)Not allow heavy dirty and solder ball on PCB.(The size of dirty refer to point and dust defect)(2)Over 50%of lead should be so

25、ldered on Land.10 Wire(1)Copper wire should not be rusted(2)Not allow crack on copper wire connection.(3)Not allow reversing the position of the flat cable.(4)Not allow exposed copper wire inside the flat cable.11*PCB(1)Not allow screw rust or damage.(2)Not allow missing or wrong putting of componen

26、t.Wincom Tech.CO.,LTD.WO12864-GC-01-SFYLYHC06(with PCB)PAGE:15/15 NO.Item Criterion 12 Protruded W:Terminal Width Acceptable criteria:Y 0.4 13 TAB 1.Position W11/3W H11/3H 2 TAB bonding strength test P(=F/TAB bonding width)650gf/cm,(speed rate:1mm/min)5pcs per SOA(shipment)14 Total no.of acceptable Defect A.Zone Maximum 2 minor non-conformities per one unit.Defect distance:each point to be separated over 10mm B.Zone It is acceptable when it is no trouble for quality and assembly in customers end product.