[]-机械加工毕业设计外文翻译--微孔的加工方法-其他专业.docx

《[]-机械加工毕业设计外文翻译--微孔的加工方法-其他专业.docx》由会员分享，可在线阅读，更多相关《[]-机械加工毕业设计外文翻译--微孔的加工方法-其他专业.docx（14页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、外文原文Options for micro-holemakingAs in the macroscale-machining world, holemaking is one of the most if not the mostfrequently performed operations for micromachining. Many options exist for how those holes are created. Each has its advantages and limitations, depending on the required hole diameter

2、and depth, workpiece material and equipment requirements. This article covers holemaking with through-coolant drills and those without coolant holes, plunge milling, microdrilling using sinker EDMs and laser drilling. Helpful Holes Getting coolant to the drill tip while the tool is cutting helps red

3、uce the amount of heat at the tool/workpiece interface and evacuate chips regardless of hole diameter. But through-coolant capability is especially helpful when deep-hole microdrilling because the tools are delicate and prone to failure when experiencing recutting of chips, chip packing and too much

4、 exposure to carbides worst enemyheat.When applying flood coolant, the drill itself blocks access to the cutting action. “Somewhere about 3 to 5 diameters deep, the coolant has trouble getting down to the tip,” said Jeff Davis, vice president of engineering for Harvey Tool Co., Rowley, Mass. “It bec

5、omes wise to use a coolant-fed drill at that point.” In addition, flood coolant can cause more harm than good when microholemaking. “The pressure from the flood coolant can sometimes snap fragile drills as they enter the part,” Davis said. The toolmaker offers a line of through-coolant drills with d

6、iameters from 0.039 to 0.125 that are able to produce holes up to 12 diameters deep, as well as microdrills without coolant holes from 0.002 to 0.020. Having through-coolant capacity isnt enough, though. Coolant needs to flow at a rate that enables it to clear the chips out of the hole. Davis recomm

7、ends, at a minimum, 600 to 800 psi of coolant pressure. “It works much better if you have higher pressure than that,” he added. To prevent those tiny coolant holes from becoming clogged with debris, Davis also recommends a 5m or finer coolant filter. Another recommendation is to machine a pilot, or

8、guide, hole to prevent the tool from wandering on top of the workpiece and aid in producing a straight hole. When applying a pilot drill, its important to select one with an included angle on its point thats equal to or larger than the included angle on the through-coolant drill that follows. The pi

9、lot drills diameter should also be slightly larger. For example, if the pilot drill has a 120 included angle and a smaller diameter than a through-coolant drill with a 140 included angle, “then youre catching the coolant-fed drills corners and knocking those corners off,” Davis said, which damages t

10、he drill. Although not mandatory, pecking is a good practice when microdrilling deep holes. Davis suggests a pecking cycle that is 30 to 50 percent of the diameter per peck depth, depending on the workpiece material. This clears the chips, preventing them from packing in the flute valleys.Lubricious

11、 ChillTo further aid chip evacuation, Davis recommends applying an oil-based metalworking fluid instead of a waterbased coolant because oil provides greater lubricity. But if a shop prefers using coolant, the fluid should include EP (extreme pressure) additives to increase lubricity and minimize foa

12、ming. “If youve got a lot of foam,” Davis noted, “the chips arent being pulled out the way they are supposed to be.” He added that another way to enhance a tools slipperiness while extending its life is with a coating, such as titanium aluminum nitride. TiAlN has a high hardness and is an effective

13、coating for reducing heats impact when drilling difficult-to-machine materials, like stainless steel. David Burton, general manager of Performance Micro Tool, Janesville, Wis., disagrees with the idea of coating microtools on the smaller end of the spectrum. “Coatings on tools below 0.020 typically

14、have a negative effect on every machining aspect, from the quality of the initial cut to tool life,” he said. Thats because coatings are not thin enough and negatively alter the rake and relief angles when applied to tiny tools. However, work continues on the development of thinner coatings, and Bur

15、ton indicated that Performance Micro Tool, which produces microendmills and microrouters and resells microdrills, is working on a project with others to create a submicron-thickness coating. “Were probably 6 months to 1 year from testing it in the market,” Burton said. The microdrills Performance of

16、fers are basically circuit-board drills, which are also effective for cutting metal. All the tools are without through-coolant capability. “I had a customer drill a 0.004-dia. hole in stainless steel, and he was amazed he could do it with a circuit-board drill,” Burton noted, adding that pecking and

17、 running at a high spindle speed increase the drills effectiveness. The requirements for how fast microtools should rotate depend on the type of CNC machines a shop uses and the tool diameter, with higher speeds needed as the diameter decreases. (Note: The equation for cutting speed is sfm = tool di

18、ameter 0.26 spindle speed.) Although relatively low, 5,000 rpm has been used successfully by Burtons customers. “We recommend that our customers find the highest rpm at the lowest possible vibrationthe sweet spot,” he said. In addition to minimizing vibration, a constant and adequate chip load is re

19、quired to penetrate the workpiece while exerting low cutting forces and to allow the rake to remove the appropriate amount of material. If the drill takes too light of a chip load, the rake face wears quickly, becoming negative, and tool life suffers. This approach is often tempting when drilling wi

20、th delicate tools. “If the customer decides he wants to baby the tool, he takes a lighter chip load,” Burton said, “and, typically, the cutting edge wears much quicker and creates a radius where the land of that radius is wider than the chip being cut. He ends up using it as a grinding tool, trying

21、to bump material away.” For tools larger than 0.001, Burton considers a chip load under 0.0001 to be “babying.” If the drill doesnt snap, premature wear can result in abysmal tool life. Too much runout can also be destructive, but how much is debatable. Burton pointed out that Performance purposely

22、designed a machine to have 0.0003 TIR to conduct in-house, worst-case milling scenarios, adding that the company is still able to mill a 0.004-wide slot “day in and day out.” He added: “You would think with 0.0003 runout and a chip load a third that, say, 0.0001 to 0.00015, the tool would break imme

23、diately because one flute would be taking the entire load and then the back end of the flute would be rubbing. When drilling, he indicated that up to 0.0003 TIR should be acceptable because once the drill is inside the hole, the cutting edges on the end of the drill continue cutting while the noncut

24、ting lands on the OD guide the tool in the same direction. Minimizing run out becomes more critical as the depth-to-diameter ratio increases. This is because the flutes are not able to absorb as much deflection as they become more engaged in the workpiece. Ultimately, too much runout causes the tool

25、 shank to orbit around the tools center while the tool tip is held steady, creating a stress point where the tool will eventually break. Taking a Plunge Although standard microdrills arent generally available below 0.002, microendmills that can be used to “plunge” a hole are. “When people want to dr

26、ill smaller than that, they use our endmills and are pretty successful,” Burton said. However, the holes cant be very deep because the tools dont have long aspect, or depth-to-diameter, ratios. Therefore, a 0.001-dia. endmill might be able to only make a hole up to 0.020 deep whereas a drill of the

27、same size can go deeper because its designed to place the load on its tip when drilling. This transfers the pressure into the shank, which absorbs it. Performance offers endmills as small as 5 microns (0.0002) but isnt keen on increasing that lines sales. “When people try to buy them, I very serious

28、ly try to talk them out of it because we dont like making them,” Burton said. Part of the problem with tools that small is the carbide grains not only need to be submicron in size but the size also needs to be consistent, in part because such a tool is comprised of fewer grains. “The 5-micron endmil

29、l probably has 10 grains holding the core together,” Burton noted. He added that he has seen carbide powder containing 0.2-micron grains, which is about half the size of whats commercially available, but it also contained grains measuring 0.5 and 0.6 microns. “It just doesnt help to have small grain

30、s if theyre not uniform.”MicrovaporizationElectrical discharge machining using a sinker EDM is another micro-holemaking option. Unlike , which create small holes for threading wire through the workpiece when wire EDMing, EDMs for producing microholes are considerably more sophisticated, accurate and

31、, of course, expensive. For producing deep microholes, a tube is applied as the electrode. For EDMing smaller but shallower holes, a solid electrode wire, or rod, is needed. “We try to use tubes as much as possible,” said Jeff Kiszonas, EDM product manager for Makino Inc., Auburn Hills, Mich. “But a

32、t some point, nobody can make a tube below a certain diameter.” He added that some suppliers offer tubes down to 0.003 in diameter for making holes as small as 0.0038. The tubes flushing hole enables creating a hole with a high depth-to-diameter ratio and helps to evacuate debris from the bottom of

33、the hole during machining. One such sinker EDM for producing holes as small as 0.00044 (11m) is Makinos Edge2 sinker EDM with fine-hole option. In Japan, the machine tool builder recently produced eight such holes in 2 minutes and 40 seconds through 0.0010-thick tungsten carbide at the hole location

34、s. The electrode was a silver-tungsten rod 0.00020 smaller than the hole being produced, to account for spark activity in the gap. When producing holes of that size, the rod, while rotating, is dressed with a charged EDM wire. The fine-hole option includes a W-axis attachment, which holds a die that

35、 guides the electrode, as well as a middle guide that prevents the electrode from bending or wobbling as it spins. With the option, the machine is appropriate for drilling hole diameters less than 0.005. Another sinker EDM for micro-holemaking is the Mitsubishi VA10 with a fine-hole jig attachment t

36、o chuck and guide the fine wire applied to erode the material. “Its a standard EDM, but with that attachment fixed to the machine, we can do microhole drilling,” said Dennis Powderly, sinker EDM product manager for MC Machinery Systems Inc., Wood Dale, Ill. He added that the EDM is also able to crea

37、te holes down to 0.0004 using a wire that rotates at up to 2,000 rpm. Turn to Tungsten EDMing is typically a slow process, and that holds true when it is used for microdrilling. “Its very slow, and the finer the details, the slower it is,” said , president and owner of Optimation Inc. The Midvale, U

38、tah, company builds Profile 24 Piezo EDMs for micromachining and also performs microEDMing on a contract-machining basis. Optimation produces tungsten electrodes using a reverse-polarity process and machines and ring-laps them to as small as 10m in diameter with 0.000020 roundness. Applying a 10m-di

39、a. electrode produces a hole about 10.5m to 11m in diameter, and blind-holes are possible with the companys EDM. The workpiece thickness for the smallest holes is up to 0.002, and the thickness can be up to 0.04 for 50m holes. After working with lasers and then with a former EDM builder to find a be

40、tter way to produce precise microholes, Jorgensen decided the best approach was DIY. “We literally started with a clean sheet of paper and did all the electronics, all the software and the whole machine from scratch,” he said. Including the software, the machine costs in the neighborhood of $180,000

41、 to $200,000. Much of the companys contract work, which is provided at a shop rate of $100 per hour, involves microEDMing exotic metals, such as gold and platinum for X-ray apertures, stainless steel for optical applications and tantalum and tungsten for the electron-beam industry. Jorgensen said th

42、e process is also appropriate for EDMing partially electrically conductive materials, such as PCD.“The customer normally doesnt care too much about the cost,” he said. “Weve done parts where theres $20,000 in time and material involved, and you can put the whole job underneath a fingernail. We do ev

43、erything under a microscope.”Light CuttingBesides carbide and tungsten, light is an appropriate “tool material” for micro-holemaking. Although most laser drilling is performed in the infrared spectrum, the SuperPulse technology from The Ex One Co., Irwin, Pa., uses a green laser beam, said Randy Gil

44、more, the companys director of laser technologies. Unlike the femtosecond variety, Super- Pulse is a nanosecond laser, and its green light operates at the 532-nanometer wavelength. The technology provides laser pulses of 4 to 5 nanoseconds in duration, and those pulses are sent in pairs with a delay

45、 of 50 to 100 nanoseconds between individual pulses. The benefits of this approach are twofold. “It greatly enhances material removal compared to other nanosecond lasers,” Gilmore said, “and greatly reduces the amount of thermal damage done to the workpiece material” because of the pulses short dura

46、tion.The minimum diameter produced with the SuperPulse laser is 45 microns, but one of the most common applications is for producing 90m to 110m holes in diesel injector nozzles made of 1mm-thick H series steel. Gilmore noted that those holes will need to be in the 50m to 70m range as emission stand

47、ards tighten because smaller holes in injector nozzles atomize diesel fuel better for more efficient burning. In addition, the technology can produce negatively tapered holes, with a smaller entrance than exit diameter, to promote better fuel flow. Another common application is drilling holes in air

48、craft turbine blades for cooling. Although the turbine material might only be 1.5mm to 2mm thick, Gilmore explained that the holes are drilled at a 25 entry angle so the air, as it comes out of the holes, hugs the airfoil surface and drags the heat away. That means the hole traverses up to 5mm of ma

49、terial. “Temperature is everything in a turbine” he said, “because in an aircraft engine, the hotter you can run the turbine, the better the fuel economy and the more thrust you get.”To further enhance the technologys competitiveness, Ex One developed a patent-pending material that is injected into a hollow-body component to block the laser beam and prevent back-wall strikes after it creates the needed hole. A