最新《EMC标准》ISO11452-1：2005道路车辆 电气电子部件对窄带辐射电磁能的抗扰性试验方法 第1部分：一般原则和术语.pdf

《最新《EMC标准》ISO11452-1：2005道路车辆 电气电子部件对窄带辐射电磁能的抗扰性试验方法 第1部分：一般原则和术语.pdf》由会员分享，可在线阅读，更多相关《最新《EMC标准》ISO11452-1：2005道路车辆 电气电子部件对窄带辐射电磁能的抗扰性试验方法 第1部分：一般原则和术语.pdf（26页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 Reference numberISO 11452-1:2005(E)ISO 2005 INTERNATIONAL STANDARD ISO11452-1Third edition2005-02-01Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 1:General principles and terminology Vhicules routiers Mthodes dessai dun quipeme

2、nt soumis des perturbations lectriques par rayonnement dnergie lectromagntique en bande troite Partie 1:Principes gnraux et terminologie Copyright International Organization for Standardization Reproduced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted without lic

3、ense from IHS-,-,-ISO 11452-1:2005(E)PDF disclaimer This PDF file may contain embedded typefaces.In accordance with Adobes licensing policy,this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the

4、editing.In downloading this file,parties accept therein the responsibility of not infringing Adobes licensing policy.The ISO Central Secretariat accepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be f

5、ound in the General Info relative to the file;the PDF-creation parameters were optimized for printing.Every care has been taken to ensure that the file is suitable for use by ISO member bodies.In the unlikely event that a problem relating to it is found,please inform the Central Secretariat at the a

6、ddress given below.ISO 2005 All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either ISO at the address below or ISOs me

7、mber body in the country of the requester.ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.+41 22 749 01 11 Fax +41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reserved Copyright International Organization for Standardization Reprodu

8、ced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 11452-1:2005(E)ISO 2005 All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope.1 2 Terms and definitions.1 3 General aim and practical use.5 4 General test condi

9、tions.6 5 Instrumentation.9 6 Test procedure.10 Annex A(normative)Functional performance status classification(FPSC).13 Annex B(informative)Constant peak test level.16 Bibliography.19 Copyright International Organization for Standardization Reproduced by IHS under license with ISO Not for ResaleNo r

10、eproduction or networking permitted without license from IHS-,-,-ISO 11452-1:2005(E)iv ISO 2005 All rights reserved Foreword ISO(the International Organization for Standardization)is a worldwide federation of national standards bodies(ISO member bodies).The work of preparing International Standards

11、is normally carried out through ISO technical committees.Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.International organizations,governmental and non-governmental,in liaison with ISO,also take part in

12、 the work.ISO collaborates closely with the International Electrotechnical Commission(IEC)on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,Part 2.The main task of technical committees is to prepare Int

13、ernational Standards.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75%of the member bodies casting a vote.Attention is drawn to the possibility that some of the e

14、lements of this document may be the subject of patent rights.ISO shall not be held responsible for identifying any or all such patent rights.ISO 11452-1 was prepared by Technical Committee ISO/TC 22,Road vehicles,Subcommittee SC 3,Electrical and electronic equipment.This third edition cancels and re

15、places the second edition(ISO 11452-1:2001),which has been technically revised.ISO 11452 consists of the following parts,under the general title Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy:Part 1:General principles and terminology

16、Part 2:Absorber-lined shielded enclosure Part 3:Transverse electromagnetic mode(TEM)cell Part 4:Bulk current injection(BCI)Part 5:Stripline Part 7:Direct radio frequency(RF)power injection Radiating loop method is to form the subject of a future part 8.Copyright International Organization for Standa

17、rdization Reproduced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 11452-1:2005(E)ISO 2005 All rights reserved v Introduction In recent years,an increasing number of electronic devices for controlling,monitoring and displaying a

18、variety of functions have been introduced into vehicle designs.It is necessary to consider the electrical and electromagnetic environment in which these devices operate.Electrical and radio-frequency disturbances occur during normal operation of many items of motor vehicle equipment.They are generat

19、ed over a wide frequency range with various electrical characteristics and can be distributed to on-board electronic devices and systems by conduction,radiation or both.Narrowband signals generated from sources on or off the vehicle can also be coupled into the electrical or electronic system,affect

20、ing the normal performance of electronic devices.Such sources of narrowband electromagnetic disturbances include mobile radios and broadcast transmitters.The characteristics of the immunity of components to radiated disturbances have to be established.ISO 11452 provides various test methods for the

21、evaluation of component immunity characteristics.Not all test methods need be used for a given device under test(DUT).For example,stripline,transverse electromagnetic(TEM)cell and parallel plate test methods provide very similar exposure to the DUT.Only those tests necessary for replicating the use

22、and mounting location of the DUT need to be included in the test plan.This will help to ensure a technically and economically optimized design for potentially susceptible components and systems.ISO 11452 is not intended as a product specification and cannot function as one(see A.1).Therefore,no spec

23、ific values for the test severity level are given.Annex A of this part of ISO 11452 specifies a general method for functional performance status classification(FPSC),while Annex B explains the principle of constant peak test level.Typical severity levels are included in an annex of each of the other

24、 parts of ISO 11452.Protection from potential disturbances has to be considered a part of total vehicle validation as described in ISO 11451,which covers vehicle test methods.It is important to know the correlation between component and vehicle tests.Copyright International Organization for Standard

25、ization Reproduced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright International Organization for Standardization Reproduced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted without license

26、from IHS-,-,-INTERNATIONAL STANDARD ISO 11452-1:2005(E)ISO 2005 All rights reserved 1 Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 1:General principles and terminology 1 Scope This part of ISO 11452 specifies general conditions

27、,defines terms,gives practical guidelines and establishes the basic principles of the component tests used in the other parts of ISO 11452 for determining the immunity of electronic components of passenger cars and commercial vehicles to electrical disturbances from narrowband radiated electromagnet

28、ic energy,regardless of the vehicle propulsion system(e.g.spark-ignition engine,diesel engine,electric motor).The electromagnetic disturbances considered are limited to continuous narrowband electromagnetic fields.A wide frequency range(0,01 MHz to 18 000 MHz)is allowed for the immunity testing of t

29、he components in this and the other parts of ISO 11452.2 Terms and definitions For the purposes of this document,the following terms and definitions apply.2.1 absorber-lined shielded enclosure shielded enclosure/screened room with radio frequency-absorbing material on its internal ceiling and walls

30、NOTE The common practice is for the room to have a metallic floor,but absorbing material may also be used on the floor.2.2 amplitude modulation AM process by which the amplitude of a carrier wave is varied following a specified law,resulting in an AM signal 2.3 artificial network AN network inserted

31、 in the supply leads of the DUT which provides,in a given frequency range,a specified load impedance for the measurement of disturbance voltages,and which isolates the DUT from the power supply in that frequency range 2.4 broadband artificial network BAN device used in power,signal and control lines

32、 that presents a controlled impedance to the DUT over a specified frequency range while allowing the DUT to be interfaced to its support system Copyright International Organization for Standardization Reproduced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted with

33、out license from IHS-,-,-ISO 11452-1:2005(E)2 ISO 2005 All rights reserved 2.5 bulk current total amount of common mode current in a harness 2.6 compression point input signal level at which the measurement system becomes non-linear,when the output value will deviate from the value given by an ideal

34、 linear system 2.7 coupling means or device for transferring power between systems NOTE Adapted from IEC 60050-726.2.8 current injection probe device for injecting current in a conductor without interrupting the conductor and without introducing significant impedance into the associated circuits 2.9

35、 current(measuring)probe device for measuring the current in a conductor without interrupting the conductor and without introducing significant impedance into the associated circuits IEC 60050-161 2.10 degradation(of performance)undesired departure in the operational performance of any device,equipm

36、ent or system from its intended performance NOTE The term“degradation”can apply to temporary or permanent failure.IEC 60050-161 2.11 dual directional coupler four-port device consisting of two transmission lines coupled together in such a manner that a single travelling wave in any one transmission

37、line will induce a single travelling wave in the other,the direction of propagation of the latter wave being dependent upon that of the former NOTE Adapted from IEC 60050-726.2.12 electromagnetic compatibility EMC ability of equipment or system to function satisfactorily in its electromagnetic envir

38、onment without introducing intolerable electromagnetic disturbance to anything in that environment IEC 60050-161 2.13 electromagnetic disturbance any electromagnetic phenomenon which may degrade the performance of a device,equipment or system,or adversely affect living or inert matter Copyright Inte

39、rnational Organization for Standardization Reproduced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 11452-1:2005(E)ISO 2005 All rights reserved 3 EXAMPLE An electromagnetic disturbance may be an electromagnetic noise,an unwanted

40、signal or a change in the propagation medium itself.IEC 60050-161 2.14 electromagnetic interference EMI degradation of the performance of equipment,transmission channel or system caused by electromagnetic disturbance NOTE The English words“interference”and“disturbance”are often used indiscriminately

41、.IEC 60050-161 2.15 forward power power supplied by the output of an amplifier or generator 2.16 functional status performance level agreed between the customer and the supplier which is specified in the test plan 2.17 ground(reference)plane flat conductive surface whose potential is used as a commo

42、n reference IEC 60050-161 2.18 immunity(to a disturbance)ability of a device,equipment or system to perform without degradation in the presence of an electromagnetic disturbance IEC 60050-161 2.19 immunity level maximum level of a given electromagnetic disturbance incident on a particular device,equ

43、ipment or system for which it remains capable of operating at a required degree of performance IEC 60050-161 2.20 narrowband emission emission which has a bandwidth less than that of a particular measuring apparatus or receiver IEC 60050-161 2.21 net power forward power minus reflected power 2.22 po

44、larization property of sinusoidal electromagnetic wave or field vector defined at a fixed point in space by the direction of the electric field strength vector or of any specified field vector Copyright International Organization for Standardization Reproduced by IHS under license with ISO Not for R

45、esaleNo reproduction or networking permitted without license from IHS-,-,-ISO 11452-1:2005(E)4 ISO 2005 All rights reserved NOTE 1 When this direction varies with time,the property may be characterized by the locus described by the extremity of the considered field vector.NOTE 2 Adapted from IEC 600

46、50-726.2.23 pulse modulation PM process by which the amplitude of a carrier wave is varied following a specified law,resulting in a PM signal 2.24 electromagnetic radiation phenomenon by which energy in the form of electromagnetic waves emanates from a source into space NOTE By extension,the term“el

47、ectromagnetic radiation”sometimes also covers induction phenomena.IEC 60050-161 2.25 electromagnetic radiation energy transferred through space in the form of electromagnetic waves IEC 60050-161 2.26 reflected power power reflected by the load due to impedance mismatch between RF source and the load

48、 2.27 shielded enclosure screened room mesh or sheet metallic housing designed expressly for the purpose of separating electromagnetically the internal and external environment IEC 60050-161 2.28 standing wave ratio SWR voltage standing wave ratio VSWR ratio,along a transmission line,of a maximum to

49、 an adjacent minimum magnitude of a particular field component of a standing wave NOTE 1 SWR is expressed by the equation:()()1SWR1rr+=where r is the absolute value of the coefficient of reflection.NOTE 2 Adapted from IEC 60050-726.2.29 stripline terminated transmission line consisting of two parall

50、el plates between which a wave is propagated in the transverse electromagnetic mode to produce a specified field for testing purposes IEC 60050-161 Copyright International Organization for Standardization Reproduced by IHS under license with ISO Not for ResaleNo reproduction or networking permitted