春毕业设计任务书某高校学生宿舍楼设计任务书(1)(完整版).doc

《春毕业设计任务书某高校学生宿舍楼设计任务书(1)(完整版).doc》由会员分享，可在线阅读，更多相关《春毕业设计任务书某高校学生宿舍楼设计任务书(1)(完整版).doc（424页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、春毕业设计任务书某高校学生宿舍楼设计任务书(1)（完整版）(文档可以直接使用，也可根据实际需要修改使用,可编辑 欢迎下载）重庆大学网络教育学院学生毕业设计（论文）任务书批次、层次、专业_ 专科起点本科_土木工程 （工业与民用建筑方向） 校外学习中心 学生姓名_ _ _ 学号_ 一、 毕业设计（论文）题目 某高校学生宿舍楼 二、毕业设计（论文）工作自 2021年 月 日起至 2021年 月 日止 三、毕业设计（论文）内容要求：场地红线图1、建筑设计部分(必做)1.1功能要求该高校学生宿舍楼位于某大学校院内，楼层建议设置为4层或5层，结构类型建议采用框架混凝土结构体系；宿舍楼的总建筑面积：3500

2、5000平方米（5%以内），学生可以考虑宿舍楼若干需求来进行设计。要求根据周围环境，合理选择建筑体型，合理安排主入口、楼梯位置，平面布置应满足建筑功能要求和防火要求；运用建筑造型和立面构图的规律，结合平面剖面的空间组合进行建筑立面设计。1.2 建筑设计内容（1）完成下面所要求的图纸绘制，各项图幅可以自行调整，但要求布局合理。名 称比 例要 求备 注标准层平面图1:100autoCAD绘制必做正立面图1:100autoCAD绘制必做侧立面图1:100autoCAD绘制选做侧立面剖面图1:100autoCAD绘制必做，剖面图要剖到楼梯楼梯平面图1:30autoCAD绘制选做门 窗 表autoCAD

3、绘制选做，需要做出准确的统计（2） 建筑说明书一份，包括:工程概况的简要说明、设计依据、标高及建筑细部作法、门窗数量和尺寸等。1.3建筑设计参考资料（1） 房屋建筑制图统一标准（GB/T 500012021）；（2） 建筑制图标准（GB/T 501042021）；（3） 房屋建筑学，中国建筑工业出版社。（4） 民用建筑设计通则（GB50352-2005）（5）建筑设计防火规范（GB50016-2021）2.结构设计部分(可与施工组织设计部分二选一)2.1结构设计资料（1）气象资料：夏季最高气温，冬季室外气温最低；基本风荷载；年降水量680mm。（2）地质条件：建筑场地地形平坦，地基土成因类型为

4、冰水洪积层。自上而下叙述如下：新近沉积层（第一层），粉质粘土，厚度0.5-1.0米，岩性特点，团粒状大孔结构，欠压密。粉质粘土层（第二层），地质主要岩性为黄褐色分之粘土，硬塑状态，具有大孔结构，厚度约3.0米, qsk=35-40kPa。粉质粘土层（第三层），地质岩性为褐黄色粉质粘土，具微层理，含铁锰结核，可塑状态，厚度3.5米， qsk=30-35kPa。粉质粘土层（第四层），岩性为褐黄色粉质粘土，具微层理，含铁锰结核，硬塑状态，厚度未揭露，qsk=40-60kPa,qsk=1500-2000kPa。不考虑地下水。（3）地基土指标：自然容重1.90g/cm2，液限25.5，塑性指数9.1，空

5、隙比0.683，计算强度150kp/m2。（4）结构选型：钢筋混凝土柜架结构（5）地震设防烈度：7度 抗震等级：三级（6）设计地震分组：场地为1类一组Tg（s）=0.25s （7）材料：柱采用C30，纵筋采用HRB335，箍筋采用HPB235，梁采用C30，纵筋采用HRB335，箍筋采用HPB235。基础采用C25，纵筋采用HRB400，箍筋采用HPB235。（8）相关工艺：屋面做法：序 号工 艺 名 称荷 载 标 准 值1SBS防水层230mm厚细石混凝土找平243陶粒混凝土找坡（2）4150mm厚加气混凝土保温层5150mm厚现浇钢筋混凝土板6板底吊顶楼面做法：序 号工 艺 名 称荷 载

6、标 准 值1水磨石地面2150mm厚现浇钢筋混凝土板3板底吊顶墙体做法：序 号名 称工 艺1外 墙250mm厚加气混凝土砌块外贴面砖，内抹灰2内 墙200mm厚加气混凝土砌块两侧抹灰学生可以根据各自情况选择是否进行抗震设计。没有选作不会影响最后成绩；选作了的，如果完成良好，酌情给予一定加分。2.2结构设计要求：（1）结构设计计算书和图纸的具体要求，各个学习中心可以根据实际情况采用，但最少必须计算一榀两跨框架。a) 结构布置 考虑建筑功能要求，正确选取计算单元，并绘制结构平面布置图（图纸比例 1:100）；b) 截面初估 对于受弯构件，可取梁高，梁宽；c) 荷载计算 按照“结构设计条件”给出的各

7、项进行计算；d) 内力计算 竖向荷载和水平荷载分别采用分层法和D值法计算，并绘制荷载作用下框架的内力图（包括弯距图、剪力图与轴力图）；e) 内力组合 考虑各种不利、有利因素对各个控制截面进行内力组合；f) 截面设计 进行框架梁、柱截面配筋计算，并绘制下列结构施工图(1:100 各项图幅可以自行调整，但要求布局合理) ：柱平面配筋图及其大样梁平面配筋图及其大样板平面配筋图；（可选作）g) 基础设计 采用柱下钢筋混凝土独立基础，绘制基础平面布置图（图纸比例 1:100）和基础板底配筋图（图纸比例 1:20或1:30）；h) 电算复核 采用PKPM商用软件计算复核，并绘制梁、柱、板施工图（可选作）i

8、) 结构设计计算书-结构设计计算书中必须注明结构选型和结构布置的理由及设计依据，详细列出结构设计计算的各个步骤、全部的计算过程和计算结果。计算书中应附有必要的计算用图（结构及构件的关系图和结构及构件的计算简图）。计算书的书写必须整洁，不能随意涂改。（2）结构设计参考资料：a) 混凝土结构设计规范（GB 500102021）；b) 建筑结构荷载规范（GB 500092021）；c) 建筑地基基础设计规范（GB 500072021）； d) 建筑抗震设计规范（GB50011-2021）e) 建筑结构制图标准（GB/T 501052021）；f) 混凝土结构施工图平面整体表示方法制图规则和构造详图（

9、03G1011）；g) 钢筋混凝土结构构造手册；（3）结构设计时应注意的几个问题：a) 多层建筑的建筑开间、进深、层高尺寸和选用的构件类型应尽量减少规格，非承重隔墙应采用轻质材料；b) 结构选型应根据功能要求、荷载大小、施工能力和场地条件进行，要求构造简单、以便于施工；c) 多层建筑结构布置在满足建筑功能、工艺和生产使用要求的同时，力求平面和竖向形式简单、整洁；柱网对称、刚度适当、荷载分布均匀，结构传力简捷，构件受力明确。3.施工组织设计部分（可与结构设计部分二选一）3.1施工设计内容工程概况 （1） 建筑结构概述：包括建筑物的功能、建筑面积（规模）、平面组合、高度、层数、层高 (应附平、立、

10、剖简图)、结构特征（基础形式、结构形式、跨度）等。 （2） 建筑地点的特征：包括位置、地形、工程地质，不同深度的土壤分析，地下水位、水质、气温、冬雨季时间，主导风向，风力和地震烈度等。 （3） 施工条件：包括三通一平情况、材料、预制加工品的供应情况以及施工单位的机械、运输、劳动力情况和企业管理情况等。 （4） 施工中的重点、难点和关键技术问题 施工方案的制定和施工方法的选择 （1） 施工布署、划分施工段、确定施工流向和施工顺序 （2） 选择确定分部分项（主要工种工程）的施工方法（重点） （3） 选择先进合理的施工方法及机械设备（4） 保证质量及安全生产的技术组织措施。 编制单位工程施工进度计划

11、 （1）拟定划分分部分项工程，确定其工作内容和名称（2）根据工程量计算规则，计算分部分项工程的工程量（3）根据劳动定额计算分部分项工程的劳动量（4）应用流水施工原理编制施工进度计划（重点）：主导工程施工进度计划（可用网络图表示）、单位工程施工进度计划 (可用横道图或网络图表示)（5）编制资源供应计划：主要机具设备供应计划、劳动力供应计划、主要建筑材料(或成品、半成品)供应计划 绘制单位工程施工平面图 施工平面图须按主导工程施工时的现场布置要求进行设计，绘制一张2号图，施工平面图的内容有：（1） 总平面图中已建和拟建建筑物、构筑物及其它设施（2） 垂直运输机械的布置行走式起重机械的开行路线，停机

12、点位置；固定式起重机械所在位置及服务半径。 （3） 为施工服务的生产设施（场内仓库、或堆场、与辅助性生产设施：如混凝土搅拌站、砂浆搅拌站、木工房、钢筋加工棚等占地面积的计算及其位置的确定）（4） 为施工服务的生活设施（办公用房、食堂、厕所、开水房等）（5） 场内临时道路、场内供水管网、场内供电线路的布置（6） 防火、安全等设施的布置（7）其它（围墙、门卫、大门等）3.2施工设计成果（1）单位工程施工组织设计（进度计划和平面图布置图为其附件）（2）单位工程施工进度计划（横道图或网络图）（CAD图纸或EXCEL表格）（3）单位工程施工平面图（按主体工程施工阶段布置）（图纸比例 1:200或1:50

13、0）3.3、施工设计参考资料（1）建筑施工组织；（2）建筑施工手册；（3）建筑工程施工质量验收统一标准（GB503002001）；(4) 建筑安装工程统一劳动定额(5) 施工定额 (6) 施工机械手册4.格式要求4.1图 纸图纸一律使用A2（420mm594mm），格式如下：（dwg格式请在学院首页下载专区毕业设计专栏下载使用）4.2正文正文参考标准格式范本（在毕业设计专栏下载使用），正文采用A4纸竖排（60页以上的论文采用双面打印，60页及其60页以下论文采用单面打印）上边距：2.5cm 、下边距：2.5cm、左边距：3.0cm、右边据：2.5cm行距：1.5倍正文字体使用小四号字，宋体，一

14、级标题使用四号字体，黑体，加粗；二级标题使用小四号字体，黑体，加粗；三级标题使用小四号字体，宋体，加粗。序号：毕业设计（论文）各章节序号采用阿拉伯数字编码，格式为：11.11.1.1（最多不超过3级）页码：阿拉伯数字进行编号，位于每页页底中部。4.3公 式用word中“公式编辑器”或“MathType 5.0 Equation”软件完成，大小为12pt（可以进行适当调整），位置居中指导教师 下发日期 附录：土木工程工民建方向毕业设计各阶段完成内容明细表平台阶段名称平台提交时间阶段进 度 计 划2图纸Word文档毕业设计第一阶段参看当前批次时间安排表建筑设计（必做）标准层平面图正立面图楼梯剖面图

15、门 窗 表楼梯平面图（可选）建筑设计说明毕业设计第二阶段结构设计（可与施工组织设计二选一）结构平面布置图结构计算书结构布置截面初估荷载计算内力计算内力组合柱平面配筋图梁平面配筋图板平面配筋图（可选）截面设计基础平面布置图基础板底配筋图PKPM施工图（可选）基础设计毕业设计第三阶段施工组织设计（可与结构设计二选一）施工现场平面图工程概况施工方案施工进度计划（横道图或网络图）资源需要量计划各项保措施说明：1）所有图纸选择autoCAD绘图（08版及以下版本），与设计文档打包压缩后上传至毕业设计平台。2）一定注意按任务书的要求进行毕业设计，特别注意规范格式，具体格式请参阅学院发的“毕业设计（论文）撰

16、写规范化要求说明及工民建毕业设计标准格式模板”及其他相关文件。注意毕业设计千万不可与其他同学雷同。学院网页首页教学专区毕业设计资料专栏上面还有其他相关文件，请一定仔细阅读，使设计顺利进行。3）土木工程专业本科设计不提交开题报告，整个设计分为三阶段：第一阶段：提交建筑设计成果第二阶段：提交结构设计成果或施工组织设计成果（二选一，建议选择施工组织设计，较简单和通用，也不容易出现原则性错误）第三阶段：将前两阶段的成果打包，整理所有资料（包括1、封面；2、摘要；3、目录；4、正文；5、任务书，具体参见“工民建毕业设计标准格式模板”）（英文版 ） Two regulations promulgated

17、for implementation is in the party in power for a long time and the rule of law conditions, the implementation of comprehensive strictly strategic plan, implementation in accordance with the rules and discipline to manage the party, strengthen inner-party supervision of major initiatives. The two re

18、gulations supporting each other, the adhere to a positive advocate, focusing on morality is of Party members and Party leading cadres can see, enough to get a high standard; around the party discipline, disciplinary ruler requirements, listed as negative list, focusing on vertical gauge, draw the pa

19、rty organizations and Party members do not touch the bottom line . Here, the main from four square face two party rules of interpretation: the first part introduces two party Revised regulations the necessity and the revision process; the second part is the interpretation of the two fundamental prin

20、ciples of the revision of laws and regulations in the party; the third part introduces two party regulations modified the main changes and needs to grasp several key problems; the fourth part on how to grasp the implementation of the two regulations of the party. and revised the necessity and revise

21、d history of the CPC Central Committee the amendment to the Chinese Communist Party members and leading cadres honest politics several guidelines and column 1 by 2021 to strengthen party laws and regulations focus. Two party regulations revision work lasted a Years, pooling the wisdom of the whole p

22、arty, ideological consensus, draw historical experience, respect for the wisdom of our predecessors, which reflects the unity of inheritance and innovation; follow the correct direction, grasp the limited goals, adhere to the partys leadership, to solve the masses of the people reflect a focus on th

23、e problem. The new revision of the and , reflects the partys 18 and the eighth session of the third, the spirit of the fourth plenary session, reflecting the experience of studying and implementing the General Secretary Xi Jinping series of important speech, reflects the partys eighteen years compre

24、hensive strictly practice. (a) revised two regulations of the party need of in based on revised, the promulgation and implementation of January 2021, to strengthen the construction of the contingent of leading cadres play an important role. But with the party to manage the party strictly administeri

25、ng the deepening, has not been able to fully meet the actual needs. Content is too complicated, eight prohibition, 52 are not allowed to hard to remember, and also difficult to put into practice; the second is concisely positive advocated by the lack of prohibited provisions excessive, no autonomy r

26、equirements; the third is banned terms and discipline law, both with the party discipline, disciplinary regulations repeat and Criminal law and other laws and regulations repeat; the fourth is to clean the theme is not prominent, not for the existing problems, and is narrow, only needle of county-le

27、vel leading cadres above. is in 1997 based on revision, in December 2003 the promulgation and implementation, to strengthen the construction of the party play very important role. Along with the development of the situation, which many provisions have been unable to fully meet the comprehensive stri

28、ctly administering the practice needs. One is Ji law, more than half of the provisions and criminal law and other countries laws and regulations Repetition; two is the political discipline regulations is not prominent, not specific, for violation of the party constitution, damage the authority of Pa

29、rty Constitution of misconduct lack necessary and serious responsibility to pursue; third is the main discipline for the leading cadres, does not cover all Party members. Based on the above situation, need to and the two is likely to be more relevant regulations first amendment. By revising, really

30、put the authority of Party discipline, the seriousness in the party tree and call up the majority of Party members and cadres of the party constitution of party compasses party consciousness. (II) two party regulations revision process the Central Committee of the Communist Party of China attaches g

31、reat importance to two regulations revision . Xi Jinping, general books recorded in the Fifth Plenary Session of the eighth session of the Central Commission for Discipline Inspection, on the revised regulations made clear instructions. According to the central deployment, the Central Commission for

32、 Discipline Inspection from 2021 under six months begin study two regulations revision. The Standing Committee of the Central Commission for Discipline Inspection 4 review revised. Comrade Wang Qishan 14 times held a special meeting to study two regulations revision, amendment clarifies the directio

33、n, major issues of principle, path and target, respectively held a forum will listen to part of the province (area) secretary of the Party committee, Secretary of the Discipline Inspection Commission, part of the central ministries and state organs Department The first party committee is mainly resp

34、onsible for people, views of experts and scholars and grassroots party organizations and Party members. Approved by the Central Committee of the Communist Party of China, on 7 September 2021, the general office of the Central Committee of the Party issued a notice to solicit the provinces (autonomou

35、s regions, municipalities) Party, the central ministries and commissions, state ministries and commissions of the Party (party), the General Political Department of the military, every 3 people organization of Party of two regulations revision opinion. Central Commission for Discipline Inspection of

36、 extensive solicitation of opinions, careful study, attracting, formed a revised sent reviewers. In October 8 and October 12, Central Committee Political Bureau Standing Committee and the Political Bureau of the Central Committee After consideration of the two regulations revised draft. On October 1

37、8, the Central Committee of the Communist Party of China formally issued two regulations. Can say, two laws amendment concentrated the wisdom of the whole party, embodies the party. Second, and revision of the basic principles of two party regulations revision work and implement the partys eighteen,

38、 ten eight plenary, the spirit of the Fourth Plenary Session of the Eleventh Central Committee and General Secretary Xi Jinping important instructions on the revised and , highlighting the ruling party characteristics, serious discipline, the discipline quite in front of the law, based on the curren

39、t, a long-term, advance as a whole, with Bu Xiuding independent and . Main principle is: first, adhere to the party constitution to follow. The constitution about discipline and self-discipline required specific, awaken the party constitution of party compasses party consciousness, maintaining the a

40、uthority of the constitution. General Secretary Xi Jinping pointed out that no rules, no side round. Party constitution is the fundamental law, the party must follow the general rules. In early 2021 held the eighth session of the Central Commission for Discipline Inspection Fifth Plenary Session of

41、the 16th Central Committee, Xi Jinping again pointed out that constitution is the party must follow the general rules, but also the general rules. the revision of the and is Method in adhere to the regulations established for the purpose of combining rule of virtue is to adhere to the party constitu

42、tion as a fundamental to follow, the constitution authority set up, wake up the party constitution and party rules the sense of discipline, the party constitution about discipline and self-discipline specific requirements. 4 second is to adhere to in accordance with the regulations governing the par

43、ty and the party. The Party of rule of virtue de, mainly refers to the partys ideals and beliefs, excellent traditional style. The revised the closely linked to the self-discipline, insisting on the positive initiative, for all members, highlight the vital few, emphasized self-discipline, focusing o

44、n the morality, and the majority of Party members and the ideological and moral standards. The revised Ji method separately, Ji, Ji Yan to Method, as a negative list, emphasizing the heteronomy, focusing on vertical gauge. Is this one high and one low, a positive reaction, the strict party disciplin

45、e and practice results transformation for the integration of the whole party to observe moral and discipline requirements, for the majority of Party members and cadres provides benchmarking and ruler. Third, insist on to. In view of the problems existing in the party at the present stage, the main problems of Party members and cadres in the aspect of self-discipline and abide by the discipline to make clearly defined, especially the partys eighteen years strict political discipline and political r