ABB传感器PFEA11112中英文手册.docx

《ABB传感器PFEA11112中英文手册.docx》由会员分享，可在线阅读，更多相关《ABB传感器PFEA11112中英文手册.docx（73页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、-hapter 1 - Introduction第一章 绪论1.1 About this manual1.1 关于此手册This User Manual describes your new Measure Web Tension System. When you have read the manual, you will have the necessary knowledge for mechanical and electrical installation, commissioning, operation, preventive maintenance and basic faul

2、t tracing of your measurement system.。该手册介绍型幅面材料的张力测量系统，阅读该手册须具备对测量系统的认知，包括机械和电气安装、调试、操 作、定期检修和根本故障查寻。注：对于不同产业来说，幅面材料所指不同。幅面在钢铁工业中是指带钢；纺织工业是指布匹；造纸工业是指纸张； 塑料工业是指塑料薄膜To get the best reliability and precision out of yourmeasurement system, study this User Manual first.阅读用户手册可使你的测量系统获得最正确的牢靠性和精 密度。1.2 H

3、ow to use this manual1.2 怎么使用手册This user manual comprises two main parts.此用户手册有两个主要局部。1. Information about the Tension Electronics:1. 张力传感器的信息。- System and safety information (chapter 1)- 系统和安全信息第一章- Installation,commissioning,maintenance, operation and fault tracing (chapters 2-6)- 安装，试车，维护，操作和故障查寻

4、2-6 章- Technical data (appendix A)- 技术数据附录 A-2. InformationaboutDesigningtheLoadCell Installation:压头的安装- Vertical-force sensing load cell PFCL 301E (Appendix B)微型垂直力压头 PFCL 301E (附录 B)- Horizontal-force sensing load cell PFTL 301E (Appendix C)微型水平力压头 PFTL 301E (附录 C)- Radial-force Tensiometer PFRL 1

5、01 (Appendix径向张力计 PFRL 101附录 D- Horizontal-force sensing load cell PFTL 101 (Appendix水平力压头 PFTL 101 (附录 E)Each appendix contains detailed information about one of the above load cell types when used in web tension systems with Tension Electronics PFEA111/112.每 个 附 录 均 包 括 上 述 幅 面 张 力 系 统 使 用 到 的PFEA

6、111/112 测量装置的具体信息。1.2.1 Getting started1.2.1 开头You can use the Fast Setup sequence to set up your system for basic measurement.使用快速启动去建立根本测量系统。The Fast Setup guides you through a minimum number of steps to set up the tension electronics.快速启动可用最少的步骤去建立张力测量 。Perform the action in the following section

7、s:。Guide Section 3.6 Step-by-step Commissioning执行操作以下局部:3.6 调试步骤l Section 3.7 Performing Basic Settings3.7 演示根本设置l Section 3.8 Performing a Fast Setup3.8 演示快速设置For extended functionality, use “Performing a Complete Setup”.用“演示完全设置”可了解扩展的功能See Section 3.11 Performing a Complete Setup.演示完全设置1.2.2 Savi

8、ng actual data and settings at commissioning保存试调试时的实际参数和设定When commissioning is completed you can use the form in Appendix F, Where actual commissioning data and settings can be filled in and saved for future use.试车完成后，将数据填入附件 F 中的表单并保存，以供将来使用。1.3 About this System (关于这个系统)Your system for tension me

9、asurement consists of:张力测量系统由以下构成:Tension Electronics压力传感器PFEA111 or PFEA112张力测量装置 PFEA111 or PFEA112 PFEA111 is a cost effective compact and user friendly tension electronics providing an accurate and reliable fast analog SUM signal from two load cells for control and/or monitoring. The display can

10、 show the SUM, individual A & B and difference signal. The small size and DIN-rail mount make this unit very easy to integrate into many types of electrical cabinets.PFEA111 是一款高效紧凑的张力测量装置，且用户界面完善。可用于监控来自两路元件发出的高精度和高牢靠性的 快速模拟 SUM 信号，显示器可分别显示 A 和 B 及差值信号。该装置可以很便利地安装在电气柜的 DIN 导轨上。 PFEA112 provides the

11、 same functionality and user friendliness as the PFEA111 with the addition of fieldbus communication via Profibus-DP.PFEA112 和 PFEA111 一样，只是增加了 Profibus-DP 局域网通讯。 PFEA111 是一个本钱低、构造紧凑、用户简洁理解的压力传感器，为了掌握、监视只要供给一个来自两个负载中心准确的牢靠的类似 SUM 信号。显示器能够显示 SUM 信号和个别的微小差异的信号。其小规格的和 DIN 导轨组成这个单元格外简洁和电气柜构成一个整体。 PFEA11

12、2 供给和 PFEA111 同样的功能用户也简洁理解，它们的指令通过 Profibus-DP 进展传输。Covering a wide range of applications the Tension Electronics comes in three versions (The PFEA 113 is described in a separate manual), with different levels of performance and functionality. All three versions have multi-language digital display a

13、nd configuration keys. The configuration keys being used for setting different parameters and to check the status of the tension system. The 2x16 character display can present sum, difference or individual load cell signals. All three versions are available in both DIN-rail version (IP20-version, un

14、sealed ) and enclosed IP 65-version (NEMA 4) for mounting in more severe environments.应用于广泛领域的张力测量装置有三种不同的版本PFEA 113 是独立的手册，各具有不同性能，全部三个版本都支持多种语言数据显示器和设定键，设定键可设定各个参数，也 可检查张力测量系统的状态。2X16 字符显示器可以显示当前的和值、差值或各路独立信号。全部三个版本都可以轻松地 安装在 DIN 导轨上，并且符合 IP65 标准(NEMA 4)以应对更严酷的环境。Load cells of type PFCL 301E, PFTL

15、 301E, PFRL 101 and PFTL 101张力单元压头？规格 PFCL 301E, PFTL 301E, PFRL101 and PFTL 101.The equipment is intended for use in a wide range of manufacturing processes where a web of any kind of material, e.g. paper, plastic or textile, is transported in a machine. The only requirement is that the web is wrap

16、ped over a roll. The force on the roll is proportional to the web tension. The resulting force is transferred through the bearing housings into the load cells. The load cells create a signal is proportional to the force acting in the measuring direction of the load cells. This signal is processed an

17、d amplified in the tension electronics and can be used as an input signal for process control, presentation on a display or for registration.该设备只用于任何幅面材料的生产过程，它是传输机械 量的，例如造纸、塑料和纺织。要求幅面材料被缠绕在圆筒 棍上，圆筒棍的受力与的幅面材料的张力是成比例的，这个 力又被安装在轴承座的压力传感器压头接收，压力传感 器压头产生一个成比例的且带有方向的信号，该信号又 被张力测量装置进展放大和处理，可作为过程掌握的输入信 号、在

18、显示器上显示或存储。1.4 Safety Instructions1.4 安全说明Read and follow the safety instructions given in this section before starting any work. However, local statutory regulations, if stricter, are to take precedence.在进展任何操作前请阅读说明书，如有本地法规规定则优先。The tension measurement system contains no moving parts. However, the

19、load cells are mounted close to a rotating roll over which a web is running.张力测量系统没有任何移动部件。测压元件也安在一个 旋转的辊上。1.4.1 Personnel Safety1.4.1 人身安全WARNING 警告Never work with the load cells, or nearby, when the production line is in service. Before starting any work, switch off and lock the operating switch o

20、f the drive section for the measuring roll.当生产线工作时，不要在压力传感器或者四周进展工作。开头操作前，须切断和锁定测量辊的驱动部件的操作开 关。DANGER 危急Switch off and lock the mains operating switch to the tension electronics before performing any work on the tension electronics. When the work is completed, check that there are no loose wires, an

21、d that all units are properly secured.在装置运行前须切断和锁定主操作开关，当工作完毕后检查是否有松动的电缆以及整个单元都是否安全。NOTE 留意All personnel working with the installation must know the location of the main power supply switch to the measurement system and how it is operated.全部安装人员须了解本地电源开关到测量系统的接线原意是本地电源开关到测量系统，怎样操作1.4.2 Equipment Saf

22、ety1.4.3 设备安全CAUTION 留神Always switch off the mains supply voltage to the measurement system before replacing a unit.更换单元时要切断测量系统的主电源。CAUTION 留神Handle the electronic unit carefully to reduce the risk of damage from Electric Static Discharge (ESD. Note the warning label on the circuit boards.触摸电子单元要留神

23、以削减静电放电所导致的损害。注意电路盖板上的警告标志。1.5 The Measuring Technique Based on Pressductor Technology1.6 建立在压力传感器技术上的测量技术The operating principle of a force transducer has a great effect on how well it will perform. It also affects how stiff and vibration-free the entire load cell will be as well as its robustness

24、and tolerance to overload. All of these factors impact on the design, operation, and maintenance of the web processing machinery.假设使用得当，力传感器的工作原理可获得最正确效 果，它还取决于其结实度以及整个压力传感器压头在无 振动时的稳定度和过载力量。ABBs Pressductor transducer technology produces asignal as a result of changes in an electromagnetic field wh

25、en the load cell is subjected to mechanical force. It is an operating principle that has its origin in a metallurgical phenomenon according to which mechanical forces alter the ability of some steels to convey a magnetic field. Unlike other types of load cell technologies, physical movement such as

26、compression, bending or stretching is not required for signal generation.当一个机械力作用于ABB 的 Pressductor 压力传感器时，将引起传感器内部磁场会发生变化从而产生一个信号。居于 冶金学现象，该机械力转变某些钢传输的磁场的力量。而对 于其它类型的测压元件，无论压缩、弯曲和拉伸等物理现象 都不会发生作用。A Pressductor transducer (the sensor inside the load cell) is a simple and elegant design. Essentially,

27、two perpendicular windings of copper wire around a steel core combine to provide a measurement signal.放置在压头里的压力传感器是一个格外简洁的设计。实 际上就是两个由铜线围绕铁心组成相互垂直的的线圈供给的信号。An electromagnetic field is created by continuouslyfeeding an alternating current to one of the windings. The filed is positioned in such a way

28、that, since the windings are at right angles to each other, there is no magnetic coupling between them when the load cell is unstressed.连续不断的给其中一组线圈通上沟通电流能产生电磁场，由于线圈的位置是相互垂直的，所以在不受力时另一组 线圈是没有耦合的。However, then the transducer is subjected to a force,as shown in the figure, the magnetic field pattern c

29、hanges. A portion of the field couples with the second winding and induces an AC voltage that reflects the tension exerted by the web on the measurement roll. This voltage-a comparativelystrong transducer signal-is converted by the load cell systems tension electronics into a system output.固然，在压力传感器

30、收到外力时，磁场的模式发生了变 化理解是磁路发生了变化，一局部磁场耦合到另一个线圈从而产生一个沟通电压，这个沟通电压就是安装在的测量 棍上幅面材料的张力状态。这个电压信号 -相对强的压力传感器的信号-张力测量装置转换成一个系统的输出。如图Chapter 2 Installation (第 2 章 安装)2.1 About this ChapterThe way you install your system has more influence on its functionality, accuracy and reliability than you might think. The mo

31、re accurate the installation, the better the measurement system. By following the instructions in this chapter, you will fulfill the most important requirements for proper mechanical and electrical installation.The equipment is a precision instrument which although intended for severe operating cond

32、itions, must be handled with care.安装系统的方法会意想不到地影响功能、精度和牢靠性。越精准的安装，系统的测量效果越好。以下章节将对机 械和电器的安装提出最重要的需求。该设备是周密仪器，必需留神处理。2.2 Safety Instructions (安全说明)Read and follow the safety instructions given in Chapter1Introduction,beforestartingany installationwork.However,localstatutory regulations, if stricter,

33、are to take precedence.在开头任何安装工作之前，需认真阅读并遵守第 1 章的安全须知。如当地的法律法规，更严格的，要优先考虑。2.3 Mounting the load cells (测压元件安装)Installation requirements and mounting instructions are give in:安装所要求的必被条件和装配说明书 Appendix B PFCL 301E-Designing the Load Cell Installation Appendix C PFTL 301E-Designing the Load Cell Instal

34、lation Appendix D PFRL 101-Designing the Load Cell Installation Appendix E PFTL 101-Designing the Load Cell Installation附录 B PFCL 301E- Designing 测压元件安装附录 C PFTL 301E- Designing 测压元件安装附录 D PFRL 101- Designing 测压元件安装附录 E PFTL 101- Designing 测压元件安装2.4 Installing the Electronic Unit (安装电子单元)2.4.1 Selec

35、ting and Routing the Cabling ( 选择布线路线)2.4.1.1 Recommended Cabling (推举布线路线)The cabling between the load cells and the electronic unit and electrical connections must be carefully carried out in accordance with connection diagram 3BSE028140D0065 (See the appendix for your type of load cell) or accordi

36、ng to order-specific documentation.压 头 到 张 力 测 量 装 置 的 电 缆 电 气 连 接 可 根 据3BSE028140D0065见附录中对应压头 或依据订单文件的规定。PFEA111/112Cable screens should be connected: -to an earth bar close to the IP 20-Version (unsealed)-to the earth bar fitted inside the enclosure of the IP 65-Version (NEMA 4 )电缆的屏蔽需连接到：-接地排 IP

37、20 版本未标记-接地排内置电缆附件 IP65 版本(NEMA 4 国际电器制造业协会)。External indicating instrument (not included in the ABB delivery)外部指示仪表不包括在 ABB 的交货内Mains supply ( 沟通电源 ) screen ( 屏蔽线) To control system (掌握系统) Junction Box (接线盒)Load cell signals (测压元件指令输出) Load cell excitation (测压元件鼓励输入) Load cell (压力传感器) The maximum p

38、ermitted cable resistance in the excitation circuit is shown in Table 2-1. Before commissioning, check cable resistance in the load cell excitation circuit.最大限度允许电缆电阻在鼓励电路时如表 2-1 中所示， 试车以前检测电缆电阻符合要求。 Solid conductors should not be connected to terminals. Pins should not be crimped to stranded 绞成股cor

39、es.固体导体不直接连接在接线端子上， The cable from the load cell must be a robust four core cable, see Figure 2-2. Diagonal pairs must be used for the signal circuits and excitation circuits.本译：压头的引出电缆是四芯电缆，信号线和励磁线是分别对角的，见图 2-2,。Signal信号、指令load cell excitation测压元件鼓励回路 Between the junction box and the tension electr

40、onics, signal and excitation must be routed in separate cables. For example: For example: a 2 2.5 mm cable for the excitation and a shielded 2 2 0.5 mm cable with twisted pair cores for the load cell signals.接线盒到张力测量装置的信号和励磁电缆必需分开，例如：一根 22.5 的电缆做鼓励回路和一根 220.5 的双绞屏蔽线电缆接到压头上。 Cable for synchronization

41、 of two of more tension electronics must be screened or a twisted pair.两台或两台以上的张力测量装置的同步连接电缆必需屏 蔽或者双绞。 The signal cable between the tension electronics and instruments, or process equipment, must be a screened0.5 mm cable.使用信号电缆或 0.5 的屏蔽电缆连接压力电子仪器和仪表。 Cable screens must be connected to the copper ea

42、rth bar. The screen connection maximum length is 50 mm.电缆屏蔽线必需连接铜制接地棒，屏蔽接线处最大长度 为 50mm。 The protective earth conductor of the incoming mains supply must be connected to the copper earth bar in the cubicle.主回路进线电缆的保护地线必需连接在配电室的铜制接地线上。2.4.1.2 Interference (干扰)For immunity to interference, the load cel

43、l cables should be separated as far as possible from noisy power supply cables, A minimum distance of 0.3 m (12 inches) is recommended. Where the measuring system cables meet noisy cables, they must cross at right angles.出于抗干扰考虑，压头的电缆要尽可能的远离电源电缆，至少 0.3 米12 英寸。在两根电缆相遇的地方，必需使它们穿插。2.4.1.3 Synchronizati

44、on (同步)Synchronization is not required for the wall mounted IP 65-version (NEMA 4) of the tension electronics. 对于有隔离的 IP 65-version (NEMA 4)压力电子仪器同步是不必要的If two or more IP 20-version (unsealed) tension electronics are mounted in the same cabinet they must be synchronized.假设两个或更多的 IP 20-version (unsea

45、led)压力电子仪器安装在同一个电器柜里那么它们必需同步。Synchronization is done by interconnecting the “SYNC” terminals, screw terminal X1:14, of all the units and interconnecting screw terminal X:15 of all units. A twisted pair cable or a screened cable must be used.同步是由内部 SYNC 端子完成的，用一根双绞或屏蔽电缆把全部装置的 X1:14 和 X1:15 分别连在一起。If

46、one unit is turned off or removed the remaining units are still synchronized.假设一套装置断电或拆离，剩下的装置任然保持同步。2.4.2 Mounting the Tension Electronics PFEA111/112(安装张力测量装置)2.4.2.1 IP 65-version (NEMA 4)The electronic unit is delivered in an enclosure intended for wall mounting.张力测量装置交付时是设计成墙挂式的。When choosing a

47、 place for installation, check that there will be space to open the enclosure lid fully.Also check that there is enough working space in front of the enclosure.在选择安装地点时，需留出翻开盖子的空间，同时还得 检查装置前面是否有足够的操作空间。The enclosure is fitted with six cable glands. 隔离栅配有 6 个走线密封管Inches (英寸)for cable 走线孔mounting hole

48、s 安装孔Connect the cables to terminals according cable diagrams in Appendix (B, C, D, or E) depending on installed load type.参照附录 (B, C, D, or E) 中接线图连接电缆到接线端子NOTE (留意)Do not connect solid conductors to terminals. Do not crimp pins to stranded cores.固体导体不直接连接在接线端子上，不要卷折插脚成多 股芯。NOTE (留意)The incoming mains voltage must be provid