MT和尼红产品蚀纹与拔模角关系.docx
《MT和尼红产品蚀纹与拔模角关系.docx》由会员分享,可在线阅读,更多相关《MT和尼红产品蚀纹与拔模角关系.docx(6页珍藏版)》请在淘文阁 - 分享文档赚钱的网站上搜索。
1、咬花 MT 版常用規格表每千分之一英寸, 拔模為 1-1.5Ptn.#Mold-TechDepthAAnglePtn.#Mold-TechDepthBAngleMT-110000.00041MT-112000.0034.5MT-110100.0011.5MT-112050.00254MT-110200.00152.5MT-112100.00355.5MT-110300.0023MT-112150.00456.5MT-110400.0034.5MT-112200.0057.5MT-110500.00456.5MT-112250.00456.5MT-110600.0034.5MT-112300.0
2、0254MT-110700.0034.5MT-112350.0046MT-110800.0023MT-112400.00152.5MT-110900.00355.5MT-112450.0023MT-111000.0069MT-112500.00254MT-111100.00254MT-112550.0023MT-111200.0023MT-112600.0046MT-111300.00254MT-112650.0057MT-111400.00254MT-112700.0046MT-111500.002754MT-112750.00355MT-111600.0046MT-112800.00558
3、Ptn.#Mold-TechDepthCAnglePtn.#Mold-TechDepthDAngleMT-113000.00253.5MT-114000.0023MT-113050.0057.5MT-114050.00254MT-113100.0057.5MT-114100.00355.5MT-113150.0011.5MT-114150.0023MT-113200.00254MT-114200.00254MT-113250.0034.5MT-114250.00355.5MT-113300.0023MT-114300.00710MT-113350.0023MT-114350.01015MT-1
4、13400.0034.5MT-114400.00051.5MT-113450.0034.5MT-114450.00152.5MT-113500.00355.5MT-114500.00254MT-113550.00254MT-114550.0034.5MT-113600.00355.5MT-114600.00355.5MT-113650.00457MT-114650.0057.5MT-113700.0046MT-114700.0023MT-113750.0046MT-114750.0023MT-113800.0046MT-114800.0034.5Plaque#6Plaque#7Plaque#8
5、Plaque#10Ptn.#DepthPtn.#DepthPtn.#DepthPtn.#DepthMT2290.003MT3250.003MT5880.0085MT9800.004MT3920.004MT9640.003MT8880.013MT9010.003MT5850.0035MT10380.002MT10280.0035MT9450.0065MT8890.004MT10430.002MT10670.013MT9700.002MT10130.003MT11700.0025MT11490.013MT9720.0025MT10150.0055MT11920.0015MT11530.0075MT
6、9730.0035MT10390.003MT12390.003MT12110.0095MT9740.0025MT10550.0055MT12400.003MT12260.0035MT9780.003MT10680.0055MT12410.002MT12270.0035MT9850.0025MT10700.007MT12420.002MT12280.0095MT1055-10.0001MT10740.0055MT12430.002MT12300.013MT1055-20.0045MT11290.003MT12440.0025MT12320.003MT1055-30.0005MT11590.008
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- MT 产品 拔模角 关系
限制150内