阀门标准-MSS SP-6-2007 管法兰以及阀门和管件端法兰的接触面标准精度(天选打工人).pdf

《阀门标准-MSS SP-6-2007 管法兰以及阀门和管件端法兰的接触面标准精度(天选打工人).pdf》由会员分享，可在线阅读，更多相关《阀门标准-MSS SP-6-2007 管法兰以及阀门和管件端法兰的接触面标准精度(天选打工人).pdf（6页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、 MSS SP-6-2007 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings Standard Practice Developed and Approved by the Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.127 Park Street,NE Vienna,Virginia 22180 Phone:(703)281-66

2、13 Fax:(703)281-6671 E-mail:infomss-hq.org www.mss-hq.org Copyright MSS Provided by IHS under license with MSSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MSS STANDARD PRACTICE SP-6 iThis MSS Standard Practice was developed under the consensus of the MSS Technic

3、al Committees 102,110,201,and the MSS Coordinating Committee.The content of this Standard Practice is the result of the efforts of competent and concerned volunteers to provide an effective,clear,and non-exclusive specification that will benefit the industry as a whole.This MSS Standard Practice is

4、intended as a basis for common practice by the manufacturer,the user,and the general public.The existence of an MSS Standard Practice does not in itself preclude the manufacture,sale,or use of products not conforming to the Standard Practice.Mandatory conformance is established only by reference in

5、a code,specification,sales contract,or public law,as applicable.Unless otherwise specifically noted in this MSS SP,any standard referred to herein is identified by the date of issue that was applicable to the referenced standard(s)at the date of issue of this MSS SP.(See Annex A.)U.S.customary units

6、 in this SP are the standard;the metric(SI)units are for reference only.In this Standard Practice all notes,annexes,tables,and figures are construed to be essential to the understanding of the message of the standard,and are considered part of the text unless noted as supplemental.All appendices app

7、earing in this document are construed as supplemental.Supplemental information does not include mandatory requirements.Substantive changes in this 2007 edition are“flagged”by parallel bars as shown on the margins of this paragraph.The specific detail of the change may be determined by comparing the

8、material flagged with that in the previous edition.Any part of this standard may be quoted.Credit lines should read Extracted from MSS SP-6,2007 with permission of the publisher,the Manufacturers Standardization Society.Reproduction prohibited under copyright convention unless written permission is

9、granted by the Manufacturers Standardization Society of the Valve and Fittings Industry Inc.Originally Approved December,1929 Copyright,1985 by Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.Printed in U.S.A.Copyright MSS Provided by IHS under license with MSSNot for Re

10、saleNo reproduction or networking permitted without license from IHS-,-,-标准分享网 w w w.b z f x w.c o m 免费下载MSS STANDARD PRACTICE SP-6 11.SCOPE 1.1 This Standard Practice pertains to the finish of gasket contact faces of pipe flanges and end flanges of valves and fittings.1.2 This Standard Practice is

11、intended for applications to products for which ASME B16 Standards do not contain complete facing finish requirements or for which there are no such Standards.2.DEFINITIONS 2.1 Roughness Average The term Ra(Roughness average)is expressed in micro-inches(in)micro-meters(m).2.2 Flange Facing Finish Th

12、e surface finish on the flange contact face,see Figure 1,that comes in contact with a gasket upon flange assembly.3.REQUIREMENTS 3.1 Flange facing finish shall be judged by visual comparison with Ra standards(see ASME B46.1)and not by instruments having stylus tracers and electronic amplification.Th

13、e finishes required are given in Table 1.Other finishes may be furnished by agreement between purchaser and manufacturer.3.2 Dimensions shown(in Table 1)shall not be cause for rejection by depth gage measurement or precision instrument measurements.4.LIMITATIONS 4.1 Surface finishes listed are not n

14、ecessarily optimum for all gasket types of materials.4.2 On flat faces,serrations need not extend beyond corresponding raised face diameter.STANDARD FINISHES FOR CONTACT FACES OF PIPE FLANGES AND CONNECTING END FLANGES OF VALVES AND FITTINGS FIGURE 1 Types of Contact Faces for Flanges Copyright MSS

15、Provided by IHS under license with MSSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MSS STANDARD PRACTICE SP-6 2TABLE 1 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings Type of Contact Faces Steel Ductile Iron

16、Gray Iron Bronze Flat or 1-16”(1.6 mm)Raised Face and Serrated(a):spiral or concentric,45 to 55 per inch(18 to 21 per cm)recommended.The resultant surface finish shall have a 125 to 250 in(3.2 to 6.3 m)Ra.Non-serrated(b):250 in(6.3 m)Ra max.,or Serrated(a):spiral or concentric,11 to 50 per in.(5 to

17、19 per cm).Depth approx.0.003 to 0.020 in.(0.075 to 0.51 mm)Non-serrated(b):250 in(6.3 m)Ra max.,or Serrated(a):spiral,11 to 50 per in.(5 to 19 per cm)or concentric,8 or more per in.(4 or more per cm).Depth approx.0.003 to 0.020 in.(0.075 to 0.51 mm)Non-serrated(b):125 in(3.2 m)Ra max.,or Serrated(a

18、):spiral or concentric,30 to 80 per in.(12 to 31 cm).Depth approx.0.003 to 0.020 in.(0.075 to 0.51 mm).1/4”(6.4 mm)Raised and Large Male&Female Small Male&Female,Large&Small Tongue&Groove Serrated(as above)(a)or Non-serrated:125 in.(3.2 m)Ra max.Ring Joint Side Walls of Groove Non-serrated:63 in.(1.

19、6 m)Ra max.Non-serrated:63 in.(1.6 m)Ra max.NOTES:(a)Unless otherwise specified,the manufacturer may supply either spiral or concentric grooves for serrations.The spiral machining operation is commonly accomplished with the cutting tool having 0.06 in.(1.6 mm)or larger tip radius.(b)Unless otherwise

20、 specified,the manufacturer may supply either the serrated(commonly accomplished with the cutting tool having 0.06 in.(1.6 mm)or larger tip radius)or smooth finish.Copyright MSS Provided by IHS under license with MSSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-标

21、准分享网 w w w.b z f x w.c o m 免费下载MSS STANDARD PRACTICE SP-6 3ANNEX A Referenced Standards and Applicable Dates This annex is an integral part of this Standard Practice and is placed after the main text for convenience.Standard Name or Description ASME,ANSI/ASME,ANSI,ASME/ANSI B46.1 1995 Surface Textur

22、e(Surface Roughness,Waviness,and Lay)The following organizations publish the above standard:ANSI American National Standards Institute 25 West 43rd Street 4th Floor New York NY 10036 ASME ASME International Three Park Avenue New York,NY 10016-5990 Copyright MSS Provided by IHS under license with MSS

23、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-List of MSS Standard Practices(Price List Available Upon Request)Number SP-6-2007 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings SP-9-2001 (R 05)Spot Facing for B

24、ronze,Iron and Steel Flanges SP-25-1998 Standard Marking System for Valves,Fittings,Flanges and Unions SP-42-2004 Class 150 Corrosion Resistant Gate,Glove,Angle and Check Valves with Flanged and Butt Weld Ends SP-43-1991(R 01)Wrought Stainless Steel Butt-Welding Fittings SP-44-2006 Steel Pipeline Fl

25、anges SP-45-2003 Bypass and Drain Connections SP-51-2007 Class 150LW Corrosion Resistant Flanges and Cast Flanged Fittings SP-53-1999(R 07)Quality Standard for Steel Castings and Forgings for Valves,Flanges and Fittings and Other Piping Components-Magnetic Particle Examination Method SP-54-1999(R 07

26、)Quality Standard for Steel Castings for Valves,Flanges,and Fittings and Other Piping Components-Radiographic Examination Method SP-55-2006 Quality Standard for Steel Castings for Valves,Flanges and Fittings and Other Piping Components-Visual Method for Evaluation of Surface Irregularities SP-58-200

27、2 Pipe Hangers and Supports-Materials,Design and Manufacture SP-60-2004 Connecting Flange Joint Between Tapping Sleeves and Tapping Valves SP-61-2003 Pressure Testing of Steel Valves SP-65-2004 High Pressure Chemical Industry Flanges and Threaded Stubs for Use with Lens Gaskets SP-67-2002a Butterfly

28、 Valves SP-68-1997 (R 04)High Pressure Butterfly Valves with Offset Design SP-69-2003 Pipe Hangers and Supports-Selection and Application(ANSI/MSS Edition)SP-70-2006 Gray Iron Gate Valves,Flanged and Threaded Ends SP-71-2005 Gray Iron Swing Check Valves,Flanged and Threaded Ends SP-72-1999 Ball Valv

29、es with Flanged or Butt-welding Ends for General Service SP-75-2004 Specification for High Test Wrought Butt Welding Fittings SP-77-1995(R 00)Guidelines for Pipe Support Contractual Relationships SP-78-2005a Gray Iron Plug Valves,Flanged and Threaded Ends SP-79-2004 Socket-Welding Reducer Inserts SP

30、-80-2003 Bronze Gate,Globe,Angle and Check Valves SP-81-2006 Stainless Steel,Bonnetless,Flanged,Knife Gate Valves SP-83-2006 Class 3000 Steel Pipe Unions,Socket-Welding and Threaded SP-85-2002 Gray Iron Globe&Angle Valves,Flanged and Threaded Ends SP-86-2002 Guidelines for Metric Data in Standards f

31、or Valves,Flanges,Fittings and Actuators SP-88-1993(R 01)Diaphragm Valves SP-89-2003 Pipe Hangers and Supports-Fabrication and Installation Practices SP-90-2000 Guidelines on Terminology for Pipe Hangers and Supports SP-91-1992(R 96)Guidelines for Manual Operation of Valves SP-92-1999 MSS Valve User

32、 Guide SP-93-1999(R 04)Quality Standard for Steel Castings and Forgings for Valves,Flanges,and Fittings and Other Piping Components-Liquid Penetrant Examination Method SP-94-1999 (R 04)Quality Std for Ferritic and Martensitic Steel Castings for Valves,Flanges,and Fittings and Other Piping Components

33、-Ultrasonic Examination Method SP-95-2006 Swage(d)Nipples and Bull Plugs SP-96-2001 (R 05)Guidelines on Terminology for Valves and Fittings SP-97-2006 Integrally Reinforced Forged Branch Outlet Fittings-Socket Welding,Threaded and Buttwelding Ends SP-98-2001(R 05)Protective Coatings for the Interior

34、 of Valves,Hydrants,and Fittings SP-99-1994(R 05)Instrument Valves SP-100-2002 Qualification Requirements for Elastomer Diaphragms for Nuclear Service Diaphragm Valves SP-101-1989(R 01)Part-Turn Valve Actuator Attachment-Flange and Driving Component Dimensions and Performance Characteristics SP-102-

35、1989(R 01)Multi-Turn Valve Actuator Attachment-Flange and Driving Component Dimensions and Performance Characteristics SP-104-2003 Wrought Copper Solder Joint Pressure Fittings SP-105-1996(R 05)Instrument Valves for Code Applications SP-106-2003 Cast Copper Alloy Flanges and Flanged Fittings,Class 1

36、25,150 and 300 SP-108-2002 Resilient-Seated Cast-Iron Eccentric Plug Valves SP-109-1997(R 06)Welded Fabricated Copper Solder Joint Pressure Fittings SP-110-1996 Ball Valves Threaded,Socket-Welding,Solder Joint,Grooved and Flared Ends SP-111-2001(R 05)Gray-Iron and Ductile-Iron Tapping Sleeves SP-112

37、-1999(R 04)Quality Standard for Evaluation of Cast Surface Finishes-Visual and Tactile Method.This SP must be sold with a 10-surface,three Dimensional Cast Surface Comparator,which is a necessary part of the Standard.Additional Comparators may be sold separately.SP-113-2001(R 07)Connecting Joint bet

38、ween Tapping Machines and Tapping Valves SP-114-2007 Corrosion Resistant Pipe Fittings Threaded and Socket Welding,Class 150 and 1000 SP-115-2006 Excess Flow Valves,1 1/4 NPS and Smaller,for Fuel Gas Service SP-116-2003 Service Line Valves and Fittings for Drinking Water Systems SP-117-2006 Bellows

39、Seals for Globe and Gate Valves SP-118-2007 Compact Steel Globe&Check Valves-Flanged,Flangeless,Threaded&Welding Ends(Chemical&Petroleum Refinery Service)SP-119-2003 Factory-Made Belled End Socket Welding Fittings SP-120-2006 Flexible Graphite Packing System for Rising Stem Steel Valves(Design Requi

40、rements)SP-121-2006 Qualification Testing Methods for Stem Packing for Rising Stem Steel Valves SP-122-2005 Plastic Industrial Ball Valves SP-123-1998(R 06)Non-Ferrous Threaded and Solder-Joint Unions for Use with Copper Water Tube SP-124-2001 Fabricated Tapping Sleeves SP-125-2000 Gray Iron and Duc

41、tile Iron In-Line,Spring-Loaded,Center-Guided Check Valves SP-126-2007 Steel In-Line Spring-Assisted Center Guided Check Valves SP-127-2001 Bracing for Piping Systems Seismic-Wind-Dynamic Design,Selection,Application SP-128-2006 Ductile Iron Gate Valves SP-129-2003 Copper-Nickel Socket-Welding Fitti

42、ngs and Unions SP-130-2003 Bellows Seals for Instrument Valves SP-131-2004 Metallic Manually Operated Gas Distribution Valves SP-132-2004 Compression Packing Systems for Instrument Valves SP-133-2005 Excess Flow Valves for Low Pressure Fuel Gas Appliances SP-134-2006a Valves for Cryogenic Service In

43、cluding Requirements for Body/Bonnet Extensions SP-135-2006 High Pressure Steel Knife Gate Valves SP-136-2007 Ductile Iron Swing Check Valves(R-YEAR)Indicates year standard reaffirmed without substantive changes A large number of former MSS Practices have been approved by the ANSI or ANSI Standards,

44、published by others.In order to maintain a single source of authoritative information,the MSS withdraws its Standard Practices in such cases.Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.127 Park Street,N.E.,Vienna,VA 22180-4620(703)281-6613 Fax#(703)281-6671 MSS-IHS SP Copyright MSS Provided by IHS under license with MSSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-标准分享网 w w w.b z f x w.c o m 免费下载