阀门标准-BS EN 736-1-1995(天选打工人).pdf

《阀门标准-BS EN 736-1-1995(天选打工人).pdf》由会员分享，可在线阅读，更多相关《阀门标准-BS EN 736-1-1995(天选打工人).pdf（11页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、3404589 O086976 898 BRITISH STANDARD Valves-BS EN Terminology Part 1.Definition of types of valves The European Standard EN 736-1:1995 has the status of a British Standard 736-1:1995 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction

2、or networking permitted without license from IHS-,-,-3404589 O086977 724 M BS EN 736-1:1995 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Echnical Committee PSE/7,Valves,upon which the following bodies were represented:Amalgamated Engineer

3、ing Union Association of Bronze and Brass Founders British Chemical Engineering Contractors Association British Foundry Association British Gas plc British Plumbing Fittings Manufacturers Association British Valve and Actuator Manufacturers Association British Water Chartered Institution of Building

4、 Services Engineers Electricity Association Energy Industries Council Engineering Equipment and Materiais Users Association GAMBICA(BEAMA Ltd.)Health and Safety Executive Institution of Mechanical Engineers LP Gas Association Ministry of Defence Pipe Line Industries Guild Society of British Water In

5、dustries Water Services Association of England and Wales West Midlands CBI Coopted members This British Standard,having been prepared under the direction of the Engineering Sector Board,was published under the authority of the Standards Board and comes into effect on 15 July 1995 0 BSI 1995 Amendmen

6、ts issued since publication Amd.No.I Date I Ext affected The following BSI references relate to the work on this standard:Committee reference PSE/7 Draft for comment 92/76141 DC ISBN O 580 24276 5 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo

7、 reproduction or networking permitted without license from IHS-,-,-m 3404589 0086978 660=_ BS EN 736-1:1995 Contents m!e Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 736-1 3 i Copyright European Committee for Standardization Provided by IHS under license with

8、CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3404589 0086979 5T BS EN 736-1:1995 National foreword This British Standard has been prepared by kchnical Committee PSE/7 and is the English language version of EN 736-1:1995 Vulves-i n o l o g y Part 1:Definition

9、o f types of vulves,published by the European Committee for Standardization(CEN).EN 736-1 was produced as a result of international discussions in which the United Kingdom took an active part.Compliance with a British Standard does not of itself confer immunity from legal obligations.ii Copyright Eu

10、ropean Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3404589 0086980 217=EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 736-1 February 1995 ICs 01.040.23;23.060.00 Descriptors:valves and fi

11、ttings,vocabulary,classifications,designations English version Valves-Terminology Part 1:Definition of types of valves Appareils de robinetterie-Terminologie-Partie 1:Dfinition des types dappareil Armaturen-Terminologie-Teil 1:Definition der Grundbauarten This European Standard was approved by CEN o

12、n 1995-02-01.CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be o

13、btained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions(English,French,German).A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secret

14、ariat has the same status as the official versions.CEN members are the national standards bodies of Austria,Belgium,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden,Switzerland and United Kingdom.CEN European Committee for Standardizatio

15、n Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat:rue de Stassart 36,B-1050 Brussels O 1995 Copyright reserved to CEN members Ref.No.EN 736-1:1995 E Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction

16、or networking permitted without license from IHS-,-,-3404589 008bBII II55=Page 2 EN 7361:1995 Foreword Contents This European Standard has been prepared by the%chnical Committee CEN/TC 69,Industrial valves,the secretariat of which is held by AFNOR.This European Standard shall be given the status of

17、a national standard,either by publication of an 3 Definition 2 Normative reference identical text or by endorsement,at the latest by August 1995,and conflicting national standards shall be withdrawn at the latest by August 1995.vpes of related to design Types of valves related to function 5 Accordin

18、g to the CENKENELEC Internal Regulations,the following countries are bound to implement this European Standard:Austria,Belgium,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden,Switzerland,United Kingdom.m3e 3 3 3 3 6 Copyright European C

19、ommittee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3404589 0086982 091=Page 3 EN 736-1:1995 1 Scope This standard gives the denominations of valves.It has the purpose to provide a uniform and systemati

20、c terminology for all types of valves.By reasons of classification of terms,clause 4 defines terms related to basic design characteristics and clause 5 defines terms related to functional characteristics of valves.2 Normative reference This European Standard incorporates by dated or undated referenc

21、e,provisions from other publications.These normative references are cited at the appropriate places in the text and the publications are listed hereafter.For dated references,subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in

22、it by amendment or revision.For undated references the latest edition of the publication referred to applies.EN 736-2 Valves-lkmi?zology-Part 2:Definition of components o f valves 4.1.3 Plug and ball valves Valve in which the obturator rotates about an axis at right angle to the direction of flow an

23、d,in the open position,the flow passes through the obturator.4.1.4 Buttewu valve and eccentric plug valve Valve in which the obturator rotates about an axis at right angle to the direction of flow and,in the open position,the flow passes around the obturator.NTE.This definition also applies to swing

24、 check valves.4.1.5 Diaphragm valve Valve in which the fluid flow passage through the valve is changed by deformation of a flexible obturator.NOTE.This definition also applies to diaphragm check valves.4.2 Examples of basic types The schematic figures given below show typical designs of valves.Detai

25、ls of different body patterns and obturator designs are given in EN 736-2.4.2.1 Gate valve 3 Definition For the purposes of this standard,the following definition applies:3.1 valve Piping component which influences the fluid flow by opening,closing or partially obstructing the passage of the fluid f

26、low or by diverting or mixing the fluid flow.4 mpes of valves related to design 4.1 Basic types lhble 1 shows the basic types of valves.They are distinguished by:a)the operating motion of the obturator;b)the direction of flow in the seating area.4.1.1 Gate valve Valve in which the obturator movement

27、 is linear and,in the seating area,at right angle to the direction of flow.4.1.2 Globe valve Valve in which the obturator movement is linear and,in the seating area,in the direction of flow.NCrrE.This definition also applies to lift check valves and axial check valves.Copyright European Committee fo

28、r Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3404589 008b983 T28 Page 4 EN 736-1:1995 B C 3 U 3 3 U U O E;9 3 4 2 O tl Copyright European Committee for Standardization Provided by IHS under license with CEN

29、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-3Y04589 008698q 964 Page 5 EN 736-1:1995 4.2.2 Globe valve Globe valve Lift check valve Axial check valve 4.2.3 Plug and ball ualve Plug valve Ball valve Copyright European Committee for Standardization Provided by IH

30、S under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3404587 0086785 8 T O =Page 6 EN 736-1:1995 4.2.4 ButteMg valve and eccentric plug valve h Butterfly valve-Swing check valve-Eccentric plug valve-2.5 Diaphragm valve h Diaphragm valve I Diaphra

31、gm check valve 5&pes of valves related to function 5.1 Isolating valve Valve intended for use only in the closed or fully open position.5.2 Regulating valve Valve intended for use in any position between closed and fully open.5.3 Control valve A power operated device which changes the fluid flow rat

32、e in process control system.It consists of a valve connected to an actuator with or without positioner that is capable of changing the position of an obturator in the valve in response to a signal from the controlling system.5.4 Safety valve Valve which automatically,without the assistance of any en

33、ergy other than that of the fluid concerned,discharges a certified quantity of the fluid so as to prevent a predetermined safe pressure being exceeded,and which is designed to reclose and prevent further flow of fluid after normal pressure conditions of service have been restored.5.5 Bursting disc s

34、afety device A non-reclosing pressure relief device actuated by differential pressure and designed to function by the bursting of the bursting disc(s).It is the complete assembly of installed components including,where appropriate,the bursting disc holder.5.6 Check valve Valve which automatically op

35、ens by fluid flow in a defined direction and which automatically closes to prevent fluid flow in the reverse direction.NUE.Definitions of types of check valves are given in clauses 4.1.2,4.1.4and4.1.6.5.7 Diverting valve Valve intended to influence the proportion of two or more output flows from a c

36、ommon input flow by changing the position of the obturator.5.8 Mixing valve Valve intended to influence the proportion of two or more input flows to produce a common output flow by changing the position of the obturator.5.9 Automatic steam trap Self-contained valve which automatically drains the con

37、densate from a steam-containing enclosure whilst remaining tight to live steam or,if necessary,allowing steam to flow at a predetermined rate.Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license f

38、rom IHS-,-,-m 3404589 O086986 737 m BS EN 73&1:1995 BSI 389 Chiswick High Road London W4 4AL 9507-5-0.35k-FP BSI-British Standards Institution BSI is the independent national body responsible for preparing British Standards.It presents the UK view on standards in Europe and at the international leve

39、l.It is incorporated by Royal Charter.Contract requirements A British Standard does not purport to include all the necessary provisions of a contract.Users of British Standards are responsible for their correct application.Revisions British Standards are updated by amendment or revision.Users of Bri

40、tish Standards should make sure that they possess the latest amendments or editions.Any person who finds an inaccuracy or ambiguity while using this British Standard should bring it to the attention of the Quality Manager,BSI without delay so that the matter may be investigated swiftly.BSI offers me

41、mbers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standards Orders for all BSI,international and foreign standards publications should be addressed to Customer Services,Sales Department at Chiswick:l:O181 996

42、 7000;Fax:0181 996 7001.In response to orders for international standards,it is BSI policy to supply the BSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standards BSI provides a wide range of information on national,European and int

43、ernational standards through its Library,the Standardline Database,the BSI Information Technology Service(BITS)and its Technical Help to Exporters Service.Contact the Information Department at Chiswick:Rl:O181 996 7111;Fax:O181 996 7048.Subscribing members of BSI are kept up to date with standards d

44、evelopments and receive substantial discounts on the purchase price of standards.For details of these and other benefits contact Customer Services,Membership at Chiswick:Tel:O181 996 7002;Fax:O181 996 7001.Copyright Copyright subsists in ail BSI publications and no part may be reproduced in any form

45、 without the prior permission in writing of BSI.This does not preclude the free use,in the course of implementing the standard of necessary details such as symbols and size,type or grade designations including use by incorporation into computer programs,but where these details are reproduced includi

46、ng without limitation in printed form,in computer programs or in any other form whatsoever,the permission in writing of BSI must be obtained and if granted will be on terms including royalty,before the product is sold,licensed or otherwise exploited for commercial gain.Enquiries about copyright should be made to the Copyright Manager at Chiswick.ISBN O 580 24276 6 Product code 00542240 PSEIJ7 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-