阀门标准-BS EN 1074-3-2000 Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 3 Check valves(天选打工人).pdf

《阀门标准-BS EN 1074-3-2000 Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 3 Check valves(天选打工人).pdf》由会员分享，可在线阅读，更多相关《阀门标准-BS EN 1074-3-2000 Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 3 Check valves(天选打工人).pdf（12页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、STD.BSI BS EN 1074-3-ENGL 2000 m Lb24bbS 0859954 359 m BRITISH STANDARD Valves for water supply-Fitness for purpose requirements and appropriate verification tests-Part 3:Check valves The European Standard EN 10743:2 has the status of a British Standard ICs 23.060.50;91.140.60 NO COPYING WITHOUT BSI

2、 PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 1074-3:2000.Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National foreword This British Standard YS the official English

3、 language version of EN 107432000.The UK participation in its preparation w-as entnisted by Technical Cornuttee PSW,Valves,to Subcommittee PSW/7,Valves for the water industry,which has the responsibility to:-aid enqiirers to understand the text;-present to the responsible European committee any enqu

4、iries on the interpretation,or proposals for change,and keep the UK interests informed-monitor related international and European developments and promulgate them in the UK A list of organizations represented on t h i s subcommittee can be obtained on request to its secretary.Cross-references The Br

5、itish Standards which implement international or European publications referred to in this document niay be found in the RSI Standards Catalogue under the section entitied“International Standards Correspondence Index”,or by using the Find”facility of the BSI Standards Electronic Catalogue.A British

6、Standard does not purport to include a l l the necessary provisions of a contract.Users of British Standards are responsible for their correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pages This document comprises a front cov

7、er,an inside front cover,the EN title page,pages 2 to 9 and a back cover.The BSI copyright notice displayed in t h i s document indcates when the document was last issued.This British Standard,having been prepared under the direction of the Engineering Sector Committee,was published under the author

8、ity of the Standards Committee and comes Amendments issued since publication Comients-LI into effect on 15 July 2000-I-O BSI 07-2000 ISBN O 580 35957 3-i I:Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted wit

9、hout license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10744 April 2000 ICs 23.060.50 English version Valves for water supply-Fitness for purpose requirements and appropriate verification tests-Part 3:Check valves Robinetterie pour lalimentation en eau-Prescriptions daptitude

10、 lemploi et vrifications sy rapportant-Partie 3:Clapets de non retour Armaturen fr die Wasserversorgung-Anforderungen an die Gebrauchstauglichkeit und deren Prfung-Teil 3:Rckfluverhinderer This European Standard was approved by CEN on 26 November 1999.CEN members are bound to comply with the CENICEN

11、ELEC Internal Regulations which stipulate the conditions for giving this Europsan Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning ach national standards may be obtained on application to the Central Secretariat or to any CE

12、N member.This European Standard exists in three official versions(English,French,German).A version in any other language made by traislation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as he official versions.CEN members

13、are the national standards bodies of Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden,Switzerland and United Kingdom.EUROPEAN COMMITEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE

14、FR NORMUNG Central Secretariat:rue de Stassart,36 B-1050 Brussels O 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref.No.EN 1074-3:2000 E Copyright European Committee for Standardization Provided by IHS under license with CENNot for Resa

15、leNo reproduction or networking permitted without license from IHS-,-,-Page 2 EN 1074-3:2000 Contents Foreword.3 Introduction.3 1 Scope.4 2 Normative references.-.4 3 Definitions.4 4 Design requirements.5 5 Performance requirements.5 5.1 Mechanical strength.5 5.2 Leak-tightness.6 5.3 Hydraulic chara

16、cteristics.7 5.4 Resistance to disinfection products.7 5.5 Endurance.-7 6 Conformity assessment.7 6.1 General.7 6.2 Type tests.7 6.3 Control of production process and quality system.7 8 Packaging.7 Annex A(normative)Test method for the endurance of check valves(see 5.5).9.7 Marking.7 O BSI 07-2000 C

17、opyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-w w w.b z f x w.c o mPage 3 EN 1074-312000 Foreword This European Standard has been prepared by Technical Committee CENTTC 69,Indus

18、trial valves,the Secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard,either by publication of an identical text or by endorsement,at the latest by October 2000,and conflicting national standards shall be withdrawn at the latest by October 200

19、0.It consists of six parts:Part 1:General requirements Part 2:Isolating valves Part 3:Check valves Part 4:Air valves Part 5:Control valves Part 6:Hydrants.Part 1,in conjunction with the subsequent parts,lays down the general requirements and test procedures to be carried out in production and during

20、 the assessment of conformity of these valves(type tests).The detailed requirements,which depend on the types of valves,are defined in parts 2 to 6 of this standard.Annex A of this European standard is normative.According to the CENKENELEC Internal Regulations,the national standards organizations of

21、 the following countries are bound to implement this European Standard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg,Netherlands,Norway,Portugal,Spain,Sweden,Switzerland and the United Kingdom.Q BSI 07-2000 Copyright European Committee for Stan

22、dardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-w w w.b z f x w.c o mPage 4 EN 1074-312000 Introduction In respect of potential adverse effects on the quality of water intended for human consumption caused by the pr

23、oduct covered by this standard:1)This standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA.2)It should be noted that,while awaiting the adoption of verifiable European criteria,existing national regulations concernin

24、g the use and/or the characteristics of this product remain in force.1 Scope This European Standard defines the minimum fitness for purpose requirements for check valves to be used in,or connected to,water supply pipe systems,above or below ground(see EN 805),carrying water intended for human consum

25、ption.This standard specifies the design requirements,the performance requirements,and the conformity assessment method for check valves,whatever their type and materials.This standard applies in priority to any other product or test standard:the requirements from other standards apply only when thi

26、s standard refers to them.This standard deals with the requirements applicable to check valves up to DN 2 O00 and PFA 6 bar to PFA 25 bar.It does not apply to anti-pollution check valves which are covered by other standards.2 Normative references This European Standard incorporates,by dated or undat

27、ed references,provisions from other publications.These normative references are cited at the appropriate places in the text and the publications are listed hereafter.For dated references,subsequent amendments to or revisions of any of these publications apply to this European Standard only when inco

28、rporated in it by amendment or revision.For undated references the latest edition of the publication referred to applies.EN 736-1,Valves-Terminology-Part I Definition of the types of valves.EN 1074-1,Valves for water supply-Fitness for purpose requirements and appropriate verification tests-Pari 1:G

29、eneral requirements.EN 1267,Valves-Test of flow resistance using water as test fluid,EN 805,Water supply-Requirements for systems and components outside buildings.3 Definitions For the purpose of this standard,the definitions of EN 1074-1 apply together with the following definitions:3.1 automatical

30、ly closes to prevent fluid flow in the reverse direction(EN 736-1).check valve:Valve which automatically opens by fluid flow in a defined direction and which O BSI 07-2000 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networki

31、ng permitted without license from IHS-,-,-w w w.b z f x w.c o mSTD-BSI BS EN 107q-3-ENGL 2000 D Lb24bb9 08599bD b52 m Page 5 EN 1074-3:2000 4 Design requirements Check valves shall be designed in accordance with the requirements given in clause 4 of EN 1074-1.Check valves can be equipped with a devi

32、ce to assist closure or balance the weight of the obturator;however,such valves are not considered to have a mechanically operated obturator.The manufacturer shall indicate in the relevant technical documentation the orientations in which the check valves fulfil the requirements of this standard.5 P

33、erformance requirements 5.1 Mechanical strength 5.1.I Resistance to internal pressure of the shell and of all pressure containing components Requirement and test shall be in accordance with 5.1.I of EN 1074-1.5.1.2 Resistance of the obturator to differential pressure Requirement and test shall be in

34、 accordance with 5.1.2 of EN 1074-1.The test shall be performed with the pressure applied to the downstream side of the obturator.After the test,the obturator shall not be jammed nor wedged.After completing the test,the operating torque shall not exceed the initial operating torque by more than 1 O%

35、.5.1.3 Resistance of valves to bending Bending resistance is an optional requirement for check valves;if bending resistance is claimed by the manufacturer,the requirement and test shall be in accordance with 5.1.3 of EN 1074-1,for sizes DN 50 up to and including DN 500.The test shall be performed wi

36、th the pressure applied to the downstream side of the obturator.The bending moments M to be applied during the test shall be as given in table 1 as a function of DN,or shall be given by the manufacturers technical documentation.O BSI 07-2000 Copyright European Committee for Standardization Provided

37、by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-w w w.b z f x w.c o mSTD-BSI BS EN L07q-3-ENGL ZOO0 Lb29bb 08557bL 577 Page 6 EN 1074-3:2000 5.2 Leak-tightness Table 1-Bending moments 50 65 80 100 125 150 1050 1 400 1 500 2 200 3 200 4

38、800 200 250 300 350 400 450 500 7 200 11 O00 15 O00 19 O00 24 O00 28 O00 33 O00 5.2.1 Leak-tightness of the shell and all pressure containing components 5.2.1.I Requirement and test shall be in accordance with 5.2.1.1 of EN 1074-1.Leak-tightness to internal pressure 5.2.1.2 Leak-tightness to externa

39、l pressure Requirement and test shall be in accordance with 5.2.1.2 of EN 1074-1.5.2.2 Seat tightness 5.2.2.1 Seat tightness at high differential pressure Requirement and test shall be in accordance with 5.2.2.1 of EN 1074-1.For a type test,the test duration shall be not less than 10 min.The test sh

40、all be performed with the pressure applied to the downstream side of the obturator.5.2.2.2 Seat tightness at low differential pressure Requirement and test shall be in accordarice with 5.2.2.2 of EN 1074-1,with the test duration given in 5.2.2.1.The test shall be performed with the pressure applied

41、to the downstream side of the obturator.O BSI 07-2000 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-w w w.b z f x w.c o m STD.BS1 BS EN 107V-3-ENGL 2000 m 1b2Libb O599b2 Li25 m

42、 Page 7 EN 1074-312000 5.3 Hydraulic characteristics Requirement shall be in accordance with 5.3 of EN 1074-1;the characteristic given by the manufacturer shall be the head loss as a function of flow.When measured with a test installation in accordance with clause 4 of EN 1267,the head loss shall be

43、 not more than 1,l times the value indicated by the manufacturer.Testing is not required for check valves greater than DN 300.5.4 Resistance to disinfection products Requirement and test shall be in accordance with 5.4 of EN 1074-1.5.5 Endurance Check valves shall keep their functional capacity afte

44、r a significant number of operations(openinglclosing cycles).When,in order to verify this requirement,a check valve has been subjected to a test in accordance with annex A,comprising 2 500 opening/closing cycles,it shall still pass the leak-tightness tests in accordance with 5.2.1 and 5.2.2 and no b

45、reakage of any part shall be detected by visual inspection after dismantling the valve.Testing is not required for check valves greater than DN 300.6 Conformity assessment 6.1 General Requirement shall be in accordance with 6.1 of EN 1074-1.6.2 Type tests Requirement shall be in accordance with 6.2

46、of EN 1074-1;the type tests to be performed shall be those given in table 2.They shall take place with the valve in the horizontal position,or in the position indicated by the manufacturer depending on the possibilities of use of the check valve.6.3 Control of production process and quality system R

47、equirement shall be in accordance with 6.3 of EN 1074-1;the production control tests in table 2 are informative.7 Marking Requirement shall be in accordance with clause 7 of EN 1074-1.In addition,the direction of flow shall be marked.8 Packaging Requirement shall be in accordance with clause 8 of EN

48、 1074-1.Q BSI 07-2000 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-w w w.b z f x w.c o mPage 8 EN 1074-3:2000 Sub-clause a 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9-4.10 4.11 5.1.1

49、5.1.2 5.1.3 5.2.1.1 5.2.1.2 5.2.2.1 5.2.2.2 5.3 5.4 5.5-a The sub-clauses and requirements shown above,are those given in EN 1074-1-Table 2-Requirements and tests-Requirement a Materials DN Pressures Tempera t u res Design of the shell and obturator End types and interchangeability Operating directi

50、on Maximum water velocity All materials,including lubricants,in contact with water intended for human consumption Internal corrosion and ageing resistance External corrosion and ageing resistance Resistance to internal pressure of the shell and of all pressure containing components Resistance of the