ISO 22081-2021原版完整文件.docx

《ISO 22081-2021原版完整文件.docx》由会员分享，可在线阅读，更多相关《ISO 22081-2021原版完整文件.docx（22页珍藏版）》请在淘文阁 - 分享文档赚钱的网站上搜索。

1、INTERNATIONAL STANDARDISO 22081First edition2021-02Geometrical product specifications (GPS) Geometrical tolerancing General geometrical specifications and general size specificationsSpcification gomtrique des produits (GPS) Tolrancement gomtrique Spcifications gomtriques gnrales et spcifications de

2、taille gnralesReference number ISO 22081:2021(E) ISO 2021ISO 22081:2021(E)v ISO 2021 All rights reserved ISO 2021COPYRIGHT PROTECTED DOCUMENTAll rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be reproduced or utilized ot

3、herwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright offic

4、eCP 401 Ch. de Blandonnet 8 CH-1214 Vernier, Geneva Phone: +41 22 749 01 11Email: copyrightiso.orgWebsite: www.iso.orgPublished in SwitzerlandContentsPageForewordivIntroductionv1 Scope12 Normative references13 Terms and definitions14 Basic principles24.1 General24.2 Basic rule24.3 Indication in a te

5、chnical product documentation (TPD)35 General geometrical specification35.1 Rule for indicating the general geometrical specification35.2 Rule for the applicability of the general geometrical specification45.3 Rules for the datum system66 General size specifications76.1 Rule for indicating general s

6、ize specifications76.2 Rule for the applicability of general size specifications7Annex A (informative) Example of indication with reference to a table in the TPD9Annex B (informative) Examples10Annex C (informative) Relation to the GPS matrix model13Bibliography14ForewordISO (the International Organ

7、ization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establish

8、ed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

9、The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with th

10、e editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any paten

11、t rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an

12、 explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/ iso/foreword.

13、html.This document was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification, in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 290, Dimensional and geometrical product specification and verific

14、ation, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).This first edition cancels and replaces ISO 2768-2:1989, which has been technically revised. The main changes to ISO 2768-2:1989 are as follows: tools have been added to specify a general geometri

15、cal specification and a general size specification; the rules for application of general geometrical specification and general size specification have been clarified.Any feedback or questions on this document should be directed to the users national standards body. A complete listing of these bodies

16、 can be found at www.iso.org/members.html.IntroductionThis document is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO 14638). It influences chain links A, B and C of the chain of standards on size, distance, form, orientation and location.

17、The ISO/GPS matrix model given in ISO 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to the specifications made in accordance with this

18、 document, unless otherwise indicated.For more detailed information of the relation of this document to other standards and the GPS matrix model, see Annex C.This document deals with general geometrical specification and general size specifications, which can be used to reduce the number of individu

19、al specification indications in technical product documentation (TPD). Many geometrical features have individual specifications which are similar or identical. As an alternative, general geometrical specifications, general size specifications or both may be applied.All figures in this document for t

20、he 2D drawing indications have been drawn in first-angle projection with dimensions and tolerances in millimetres. It should be understood that third-angle projection and other units of measurement could have been used equally well without prejudice to the principles established.The figures in this

21、document represent either 2D drawing views or 3D axonometric views and are intended to illustrate how a specification can be fully indicated with visible annotation. For possibilities of illustrating a specification where elements of the specification may be available through a query function or oth

22、er interrogation of information on the 3D CAD model, and rules for attaching specifications to 3D CAD models, see ISO 16792.All figures are not complete and should not be seen as a way to fully specify a part. Theoretically exact dimensions (TED) which are not indicated are assumed to be obtained fr

23、om the 3D CAD model.INTERNATIONAL STANDARDISO 22081:2021(E)Geometrical product specifications (GPS) Geometrical tolerancing General geometrical specifications and general size specifications1 ScopeThis document gives rules for definition and interpretation of general geometrical specifications and g

24、eneral size specifications defined according to ISO 8015:2011, 5.12.General specifications defined in other standards, and the link to these standards, are not covered bythis document.The general geometrical specifications and general size (linear or angular) specifications defined in this document

25、apply only to integral features (including features of size).These specifications do not apply to derived features or integral lines (see ISO 17450-1 for the definitions of integral features and derived features).Dimensions other than linear or angular sizes (see ISO 14405-2) are not covered by this

26、 document.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

27、including any amendments) applies.ISO 8015, Geometrical product specifications (GPS) Fundamentals Concepts, principles and rulesISO 17450-1, Geometrical product specifications (GPS) General concepts Part 1: Model for geometrical specification and verificationISO 17450-2, Geometrical product specific

28、ations (GPS) General concepts Part 2: Basic tenets, specifications, operators, uncertainties and ambiguitiesISO 22432, Geometrical product specifications (GPS) Features utilized in specification and verificationISO 25378, Geometrical product specifications (GPS) Characteristics and conditions Defini

29、tions3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8015, ISO 17450-1, ISO 17450-2, ISO 22432 and ISO 25378 and the following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: ISO Online browsi

30、ng platform: available at https:/www.iso.org/obp IEC Electropedia: available at http:/www.electropedia.org/3.1general geometrical specificationgeometrical specification indicated in the technical product documentation (TPD) which is not an individual specification1 ISO 2021 All rights reserved3.2gen

31、eral size specificationsize specification (linear size specification or angular size specification) indicated in the technical product documentation (TPD) which is not an individual specificationNote 1 to entry: Linear size specifications are defined in ISO 14405-1. Angular size specifications are d

32、efined in ISO 14405-3.3.3integral featuregeometrical feature belonging to the real surface of the workpiece or to a surface modelNote 1 to entry: An integral feature is intrinsically defined, e.g. skin of the workpiece.Note 2 to entry: For the statement of specifications, features obtained from part

33、ition of the surface model or of real surface of workpiece shall be defined. These features, called “integral features”, are models of the different physical parts of the workpiece that have specific functions, especially those in contact with the adjacent workpieces.Note 3 to entry: An integral fea

34、ture can be identified, for example, by: a partition of the surface model; a partition of another integral feature; a collection of other integral features.SOURCE: ISO 17450-1:2011, 3.3.54 Basic principles4.1 GeneralWhen using general geometrical specifications or general size specifications, the de

35、signer should be aware of the following risks: overlooking important functional requirements; selecting unnecessarily tight tolerances regarding the functional requirement. It is the responsibility of the designer to ensure that: functional requirements are properly defined; the geometrical features

36、 influencing the functions are properly specified; the entire part, i.e. all geometrical features, is completely and unambiguously specified.General geometrical specification and general size specification are ways of minimising the number of indications in a TPD.4.2 Basic ruleThis document defines

37、two types of general specifications: general geometrical specifications; general size specifications.Rule A: only the specifications defined in Tables 1 and 2 shall be used to define general geometrical specifications, general size specifications or both on integral features.ISO 22081:2021(E)4.3 Ind

38、ication in a technical product documentation (TPD)Rule B: to apply general geometrical specifications, general size specifications or both according to this document, it shall be clearly indicated in or near the title block or in the product definition data set according to the following rules: word

39、ing General tolerances followed by a reference to this document (i.e. ISO 22081), followed by the indication of the general geometrical specifications, the indication of the general size specifications or both (see Figure 1).Figure 1 Indication of general geometrical specifications and general size

40、specificationsThe tolerance values can be defined as: single values; or variable values.Variable values may be dependent on either or both of: the dimensions of these integral features; the distance of the integral feature to the datum system (the TEDs).When variable tolerance values are used, unamb

41、iguous rules should be defined to obtain these values from a table (see Annex A) or from other documents (see Figure 2). Figure 2 Example of indications with the tolerance values tabled in a referenced document5 General geometrical specification5.1 Rule for indicating the general geometrical specifi

42、cationRule C: the general geometrical specification (see 3.1) shall be indicated with a surface profile specification (see Table 1 and Figure 3).9 ISO 2021 All rights reservedTable 1 General geometrical specificationTypeExample of specification indications in or near the title blockGeneral geometric

43、al specificationNOTE See 5.3 for datum systems.Apart from the characteristic (which can only be surface profile), any specification element from ISO 5459 and ISO 1101 may be used in general geometrical specification as long as they do not contradict the rules given in this document.5.2 Rule for the

44、applicability of the general geometrical specificationRule D: the general geometrical specification shall apply to each integral feature independently on the product, with the following exceptions (see Figure 3):1) an integral feature specified by a size specification (individual size specification

45、or general size specification);2) an integral feature or its derived feature specified by an individual geometrical specification;3) a datum feature used in the datum system defined in the datum section of the general geometrical specification (see 5.3);4) an integral feature indicated with simplifi

46、ed representation and not included in the CAD model, for example edges, fillets or screw threads.NOTE 1 General geometrical specification applies to integral features irrespective of a surface texture specification.NOTE 2 The general geometrical specifications are in accordance with the independency

47、 principle and the feature principle.NOTE 3 When individual specifications are applied on one or more portions of a single integral feature, any other portion is considered as another integral feature.团。叶汀可勹三I 10 孔 ，1，冒贮 |荨巨l冒|十| 冈0,3 C Z 厅120了General tolerances ISO 22081A回 0,75| A|B | c|Angular sizes 过 50TEDs according t